Products

Archgard

Archgard

Iron Strike

Stellar

Stellar

Archgard

Archgard

Astria

Astria

Astria

Astria

Astria

Osburn

Osburn

Osburn

Osburn

Osburn

Osburn

Osburn

Osburn

Osburn

Iron Strike

Iron Strike

Iron Strike

Iron Strike

Iron Strike

Jotul

Jotul

Jotul

Jotul

Jotul

Jotul

Jotul

Astria

Astria

Astria

Astria

Osburn

Jackson Grill

Jackson Grill

Jackson Grill

Bull Grills

Bull Grills

Bull Grills

Primo

Primo

Black Olive

Bull Grills

Bull Grills

Bull Grills

Bull Grills

Bull Grills

Bull Grills

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Simplifire

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Dimplex

Stellar

Mixing & Handling

Mixing & Handling

Features & Benefits

Application

Features & Benefits

Features & Benefits

Mixing & Handling

Mixing & Handling

Mixing & Handling

Features & Benefits

Mixing & Handling

Features & Benefits

Application

Mixing & Handling

Mixing & Handling

Application

Application

Mixing & Handling

Features & Benefits

Features & Benefits

Specifications

Mixing & Handling

Mixing & Handling

Application and Concentration

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Features & Benefits

Mixing & Handling

Mixing & Handling

Features & Benefits

Features & Benefits

Mixing & Handling

Mixing & Handling

Features & Benefits

Features & Benefits

Mixing & Handling

Mixing & Handling

Mixing & Handling

Features & Benefits

Mixing & Handling

Features & Benefits

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Features & Benefits

Features & Benefits

Slurry Property Summary

Application

Application

Application

Mixing & Handling

Mixing & Handling

Mixing & Handling

Application

Mixing & Handling

Mixing & Handling

Application

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Features & Benefits

Application

Features & Benefits

Features & Benefits

Mixing & Handling

Application

Specifications

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Mixing & Handling

Mixing & Handling

Application

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Features & Benefits

Mixing & Handling

Application

Application

Liners

MAASS Pitless Adapters

Sizes Available

Steel K-Packers

Target (NSF Certified)

PVC Casing

Standard

Sizes Available

Sizes Available

Stainless Steel Centralizers

Casing Protector Sizes Available

Sizes Available

Features & Benefits

Features & Benefits

Recommended Devices

Recommended Devices

Features & Benefits

Standard 2" HydraSleeve

SuperSleeve 2L

Sizes Available

0.2 Micron CAP300X2

Sizes Available

Components

Sizes Available

Sizes Available

Sizes Available

Sizes Available

Sizes Available

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Features

Features & Benefits

Features & Benefits

Features & Benefits

Features & Benefits

Method of Operation

Features & Benefits

Mixing & Handling

Security & Environmental Protection

Mixing & Handling

Mixing & Handling

Mixing Ratios

Application

Application

Application

Application

Mixing & Handling

Spare Parts for Assembly

Mixing & Handling

B Sizes Available

B Sizes Available

B Sizes Available

B Sizes Available

N Sizes Available

B Sizes Available

B Sizes Available

BW Casing Advancer Assembly and Parts

B Rod Gauge

B Conversion Kit & Head Assembly

B Core Barrel Kit

B Extended Core Barrel Option

B Overshot Assembly - Rolling

Hutcheson Sand Mixes

Features & Benefits

Application

Mixing & Handling

Sizes Available

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Wood

Wood

Wood

Wood

Wood

Wood

Wood

Wood

Wood

Wood

Wood

Wood

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Gas

Wood

Wood

Wood

Wood

Wood

Wood

Wood

NG

LP

NG

LP

LP

LP

LP

Charcoal

Charcoal

NG

NG

NG

NG

NG

NG

Wood

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Electric

Linear

  • Drilling fluid additive - viscosifier, foam stabilizer or flocculant
  • Anionic water soluble polymer
  • Can be used in gumbo shales
  • Holes larger than 222 mm will require higher concentrations when used as a flocculant

Avoid eye and skin contact. Should contact occur flush thoroughly with water. When Earth Pro Can-Free is added directly to the mud, some shear or moderate agitation should be applied. As a spotting fluid, Earth Pro Can-Free mixes readily with diesel or crude oil. 

CoreMix will yield in both hard and brackish water.  The recommended concentration of CoreMix ranges from 4-6 kg/m³ depending on drilling conditions.

  • Highly effective foam controller
  • Defoams mud containing fresh water or sea water
  • Effective in reducing or eliminating gas cuttings
  • Helps stabilize pump pressure by removing trapped air and gas
  • Combats mild to severe foaming
  • Dispersible in silicone water and brine but insoluble in oil

  • A very effective thinner in carbonate/bicarbonate and sulphate contaminated muds where conventional thinners have little or no effect
  • Stable up to 260°C (500°F)
  • Will also function as a gel suppressor to help reduce the fluid loss in most mud systems
  • Cost effective and effective at any pH
  • Environmentally acceptable
  • Effectiveness has been proven in fresh water gel, K+ polymer, gyp and saturated salt muds
  • Alternative to heavy metal lignosulphonates, lignites and tannins

  • Emulsion stability and fluid loss control
  • Good oil wetting performance
  • Good PV/YP ratio for the emulsified fluid

 

  • Excellent biodegradability (>60% by DOC Method) essentially non-toxic
  • Chloride free
  • Non-oil wetting
  • Non-foaming
  • Multiple absportion sites
  • Normal concentration used is 3-5 L/m³ by volume

When the solids content of oil-based fluids (high density or build-up of drilled solids) develop adverse effects on rheology Earth Pro OMD will provide a decrease in yield point and gel strengths improving the flow properties of the fluid.

Rates of addition will vary based on the severity of the solids build-up. Typical rates are between 2 – 8 L/m³.

Earth Pro Poly-Xan L disperses in water with moderate agitation. Continued mixing provides a smooth viscous fluid. It should be added slowly either through the hopper to allow proper dispersion.

Add Earth Pro Torq-Glide at the pump suction for reduction of torque and drag. It can be added as required to improve the sliding of the drill string when building or maintaining hole angle. Skin and eye protection should be observed.

Traditional

For maximum effectiveness Earth Pro XL-Defoamer should be added directly to the fluid system as close to the point of foaming (e.g. shale shaker) as possible. It may also be sprayed over the fluid through a wash gun diluted in a mineral oil mixture if necessary (e.g. over mud tanks).

Earth Pro XL-Defoamer may cause irritation to the skin and eyes. Use rubber gloves, rubber apron, mask and eye protection when using this and other liquid mud additives.

In case of skin contact, wash with water as required. In case of eye contact, wash with water for at least fifteen minutes and seek medical attention if necessary. Although stable, do not store Earth Pro XL-Defoamer near strong oxidizing agents.

  • Excellent solubility in cold conditions
  • Carefully controlled, low molecular weight
  • Saves energy costs and unnecessary delays associated with conditioning the mud
  • Improved dispersibility control over conventional PHPA’s
  • Provides added lubrication and lowers fluid loss
  • Improves filter cake quality and is readily dispersible with no formation of fish eyes
  • Environmentally friendly

Alcomer 755 / Zetag 7557 should be added through a chemical barrel at the flow line or injected directly into a centrifuge from a premixed polymer tank, usually in a 0.5% stock solution.

Add an appropriate organic or inorganic coagulant before adding Alcomer 755 / Zetag 7557. It can also be used for fluid clarification when added at the centrifuge in sumpless drilling operations.

Mix directly into the hopper at 30 minutes per sack or add (with agitation) to a chemical barrel or polymer-mixing tank. Avoid mixing too rapidly. A mask and goggles should be worn to prevent inhalation of dust and contact with eyes.

Alkapam A-1103D becomes very slippery when coming in contact with water. A spill should be cleaned up with an absorbent material.

Aquabloc HT mixes readily and may be added to a mud system through the hopper at 10-15 minutes per sack. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Traditional

Weight formula for Cal Carb Poultry Grit

Cal Carb Poultry Grit (lb/bbl) equals 945 (W2-W2) divided by 22.5-W2

Where: 

W1 = initial mud weight in ppg

W2 = desired mud weight in ppg

Calcium Chloride Powder is extremely corrosive. Utilize normal precautions for employee protection when handling chemical products. Use of appropriate respirator, gloves, goggles, and apron is recommended for employee comfort and protection.

  • Economical resource of hydroxyl ions to control pH levels
  • Concentrated chemical that is effective at small treatment levels
  • Can be used in most water based drilling fluids
  • Reduces corrosion of steel exposed to drilling fluids

Cellophane is used to provide a sealing agent supplement to other lost circulation material in water based drilling muds. It is also a basic additive in cement slurries, providing a matting effect in the control of losses. Typical rates of addition up to 2% by wt. cement are used as a preventative measure.

Chemul RHM is used to help increase low shear rheological properties. It helps in the suspension and transport of cuttings in highly deviated and horizontal wellbores. Chemul RHM helps reduce barite sag or settling in directional wells.

Although the use range may vary with well conditions the general recommended treatment is (0.7 – 4.2 L/m³) of Chemul RHM.

Citric Acid 99.5% min Water 1.0% max
Sulphated Ash 0.1% max Calcium  200 mg/L max
Chloride  50 mg/L max Iron  50 mg/L max
Oxalate  350 mg/L max Sulphate  150 mg/L max
Arsenic  3 mg/L max Heavy Metals  10 mg/L max

Drilstar HT mixes readily. It may be added through the hopper at rates of 5-10 minutes per sack when required. It is advisable to use a dust mask while it is being mixed.

Emul-Break can be added directly to the mud on surface or through the mixing system. Avoid inhalation of vapors. Do not get on skin, in eyes or on clothing. Keep container closed when not in use. Wear suitable protection for eyes and skin when handling. Use with adequate ventilation. Avoid contact with incompatible materials.

Store in cool, dry, well-ventilated area away from sources of heat, ignition and sparks. Use proper grounding techniques if product is classed as flammable or combustible. Avoid using natural rubber, use neoprene.

*Caution*: Emul-Break is a surface-active demulsifier. It is a respiratory and digestive tract irritant that should be handled with care.

Application Concentration (lb/100 gal)
Make up fluid (with polymer addition) 10-15
Normal drilling 15-25
Unconsolidated formations 25-40
Lost circulation 35-50

Gilsonite is relatively stable and of low hazard. However it should not be stored or used near strong oxidizing agents such as chlorates, nitrates or peroxides. Excessive dust is subject to combustion or explosion upon contact with spark or open flame. Use good industrial hygiene practice to avoid eye and excess skin contact. Wear a protective dust mask and goggles when handling and mixing.

Modern

HSO 0600G can be added directly to the mud system or metered into the system with a positive displacement pump. HSO 0600G is a combustible liquid, avoid heat, sparks and open flames. Avoid breathing vapor and contact with eyes, skin or clothing. Keep container closed when not in use. Use this product in a well-ventilated area.

Premix in water in the chemical barrel and add slowly to the system. Excess lime treatment will cause thickening of a bentonite based mud system.

Hydrated Lime gives off heat when mixed with water. Strong solutions have a high pH and may cause skin burns. Avoid contact with skin and eyes and wear protective clothing and goggles when handling and mixing. Store in a dry place.

Hyperdrill AF 207RD is added either at the flow line to promote solids settling in the sump or at a point prior to mechanical separation equipment.

A 0.5% stock solution is most commonly prepared using (1) one viscosity cup of polymer per 50 gallons of fresh water. It must be mixed slowly to prevent “humping” and the subsequent loss of polymer at the shaker screen.

Hyperdrill AF 207RD becomes very slippery when it comes in contact with water. A spill should be cleaned up with an absorbent material. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Mix Hyperdrill CP 905H slowly into a chemical barrel or polymer mixing tank and allow product to hydrate (approximately 1 hour). Avoid mixing too rapidly. Wear a mask and goggles to prevent dust inhalation and contact with eyes.

Hyperdrill CP 905H becomes very slippery when it comes in contact with water, therefore spills should be cleaned up with an absorbent material instead of water.

Mix Hyperdrill CP 944 slowly into a chemical barrel or polymer mixing tank and allow product to hydrate (approximately 1 hour). Avoid mixing too rapidly. Wear a mask and goggles to prevent dust inhalation and contact with eyes.

Hyperdrill CP 944 becomes very slippery when it comes in contact with water, therefore spills should be cleaned up with an absorbent material instead of water.

Mix Hyperdrill NF 301H slowly into a chemical barrel or polymer mixing tank and allow product to hydrate (approximately 1 hour). Avoid mixing too rapidly. Wear a mask and goggles to prevent dust inhalation and contact with eyes.

Hyperdrill NF 301H becomes very slippery when it comes in contact with water, therefore spills should be cleaned up with an absorbent material instead of water.

  • Acid soluble, non-fermenting and non-corrosive
  • Temperature stable, inert & non-damaging
  • Compatible with all drilling and completion fluids
  • Nodulized structure and surfactant coated for easy mixing

  • Readily available, economical and requires low treatment levels
  • Increases temperature range of polymers
  • Provides effective buffering action in high hardness and saturated salt brines

Solution preparation in pH neutral waters is rapid; however, attention to water temperature is necessary as cold waters require a much longer hydration time.

In high pH waters Natrosol Hi-Vis will dissolve much faster regardless of water temperature, however this is not recommended. Laboratory testing is recommended for loading confirmation and application. This HEC is compatible in fresh water, sea water, and salt solutions up to
saturation.

Store in a cool, dry place away from incompatible materials. Wear the appropriate safety goggles and protective equipment when handling this product.

Mix directly into mud hopper. Avoid mixing too rapidly. A mask and goggles should be worn to prevent inhalation of dust and contact with the eyes. Fresh air ventilation should be provided in the mixing area.

  • Temperature stability exceeding 200°C
  • Calcium tolerance to 75,000 ppm
  • Magnesium tolerance to 100,000 ppm
  • Complete tolerance to sodium and potassium chloride
  • Stabilization of rheological properties
  • Minimal effect on viscosity
  • Improved filter cake quality
  • Thermal stabilization of PAC and CMC to at least 154°C
  • Non-damaging to the formation
  • Low replacement levels
  • Environmentally safe

Potash mixes readily in water and can be mixed directly through the hopper. Avoid breathing dust while mixing. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Storage Precaution: Calcium oxide on its own will not burn. However, bulk powder may heat spontaneously when it comes into contact with water. Humidity or contact with water may generate sufficient heat to ignite flammable and combustible materials. In addition, the reaction of calcium oxide with a number of commonly encountered materials can generate sufficient heat to ignite nearby combustible materials. Store in a dry place.

Handling Precaution: Lime gives off heat when mixed with water. Due to its reactivity with water, all precautions should be taken to avoid skin or eye contact. It will cause severe burns to the eyes and skin. Wear goggles and protective clothing when handling this product.

Avoid inhalation of vapors. Do not get on skin, in eyes or on clothing. Keep container closed when not in use. Wear suitable protection for eyes and skin when handling. Use with adequate ventilation. Avoid contact with incompatible materials. Store in a cool, dry, well-ventilated area.

Sea Mud is mixed through the mud hopper and requires more shear (than bentonite) in order to attain its maximum yield. This product contains crystalline silica known to be carcinogenic to humans.

It is not uncommon to observe an increase in viscosity as a result of the high shear rate experienced by the drilling mud as it passes through the bit nozzles.

Consequently, although Sea Mud may be mixed as rapidly as 5 minutes per sack, allowance must be made for the increased viscosity arising from circulation through the bit.

It is advisable to use a dust mask and eye protection while mixing all powdered products.

Traditional

  • Non-hazardous and widely available
  • An effective, economic treatment for calcium removal
  • Quickly reduces soluble calcium levels and fluid pH
  • Easy to mix and use - soluble in water
  • Safe to use - noncombustible

Sodium Sulfite - Catalyzed readily decomposes. It is usually added at a concentration of one to two sacks to a barrel of water. After mixing, the mixture is covered with a 10.0-15.0 cm blanket of mineral oil to minimize absorption of oxygen from the air. It is then slowly pumped into the central stream of the mud pump suction with an injection pump. Wear suitable protection for eyes and skin when handling. Use in areas with adequate ventilation.

  • Microtox threshold that exceeds normal use concentrations
  • More efficient than regular starches
  • Nearly as efficient as cellulosics at controlling fluid loss
  • Non-fermenting and requires no biocide under normal conditions
  • Stable against drilling fluid enzyme contamination that could result in viscosity breakdown
  • Enhances shear thinning

T-352 Biocide is corrosive and will cause irreversible eye damage. Wear suitable protection for eyes and skin and ensure there is adequate ventilation in the mixing area.

Torq-Trol W can be added directly to the active mud system at any point of agitation.

Linear

Xanvis can be easily mixed through the mud hopper. Care should be taken, as with most polymers, to avoid mixing too quickly to prevent any potential for lumping. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Typical use on a small scale is for dump-bail treatments. The product is batched in small volumes according to the following blend table, and “dumped” down the wellbore using conventional rig equipment. After a period of time the cement sets, providing a small, hard plug in the problem area.

 

Approximate Working Time (Hrs:min at BHT)

Bag Size (kg) Water Req. (liters) Slurry Yield (liters) Density (kg/m³) 20°C 30°C
20 8.8 15.2 1900 > 6:00 5:00
Comprehensive Strength, MPa (18, 16, 24 hrs)* 0.1, 2.5, 10.0 0.7, 4.5, 11.0

*Note: Strengths are for reference only. Actual values may vary due to changing wellbore conditions, variations in density, and water quality. Samples should be taken at the time of treatment and observed at estimated wellbore temperature for strength development.

At temperatures below 30°C, calcium chloride can be added in a small amount, to accelerate the set time. Typical dosage is 0.5-1% w/w, depending on well depth, and wellbore temperature. Slurry viscosity and working time will be reduced proportionately.

Exercise extreme care in the addition of calcium chloride. In itself calcium chloride is a corrosive material, and will cause skin burns. If poorly mixed, it can cause excessive heat of hydration, potentially leading to a flash set of the cement.

Earth Pro Slurry Master is a toxic material. Store in a cool dry place, away from incompatible materials. It contains alcohol ethoxylates and mineral oil, which may cause irritation to sensitive skin areas. Wear the appropriate safety goggles and protective equipment when handling this product.

Always store Earth Pro FLA-6 in a dry location. It will be stable at elevated temperatures, although such conditions are not recommended under any circumstances. Use good industrial hygiene to avoid eye contact or inhalation. Wear appropriate safety equipment when handling and mixing.

Traditional

Temp Density Working Time Setting Time Time to 500 psi 24 Hr Strength
°C kg/m³ Hr Est. Hrs Hr:min psi
60 1830 2.5-3.0 4.75 10:30 1000
70 1830 2.5-3.0 4.25 10:00 1050
80 1830 2.5-3.0 4.00 9:00 1100
90 1830 2.5-3.0 4.00 8:30 1150

Barite (20.4μ) has two major functions in cementing operations:

Weighting Agent - Used where high pore pressures, unstable wellbores and deformable plastic formations are controlled by high hydrostatic pressures. Slurries with densities of up to 2280 kg/m³ (19.0 lbs/gal) can be prepared with Barite to control such wells.

Plugs - A Barite plug will seal the wellbore due to the high hydrostatic head pressure of the slurry. In addition the Barite slurry has a high filtrate loss causing it to dehydrate rapidly forming a plug. The viscosity and yield point of the Barite slurry must be kept low if the Barite is to settle and form a plug.

A table outlining the general effect of calcium chloride upon the thickening time and compressive strength is presented below. Results are based on an 1872 kg/m³ API Class A cement slurry. 

Thickening Time

API for Casing Cement Test (Hr:min) API for Squeeze Cementing Test (Hr:min)
Calcium Chloride (%) 300M Well 600M Well 1200M Well 300M Well 600M Well 1200M Well
0.0 4:40 3:63 2:25 3:30 2:49 1:52
1.0 1:55 1:30 1:04 1:30 1:20 0:54
3.0 0:50 0:47 0:41 0:48 0:43 0:37

Compressive Strengths (KPA)

Pressure Atmospheric Atmospheric Atmospheric
Temp 15°C 27°C 35°C
CaCl2 (%) 6 Hrs 12 Hrs 24 Hrs 6 Hrs 12 Hrs 24 Hrs 6 Hrs 12 Hrs 24 Hrs
0 138 483 6,481 517 2,793 13,307 1,620 7,343 18,685
1 3,172 5,413 15,790 5,861 10,618 27,442 8,067 16,272 30,717
3 5,206 6,585 16,686 7,550 11,549 27,442 8,446 16,030 31,372

Oilfield Cementing: Typical concentration can vary from 0.5% to 2% BWOC. CRM-22B has a synergistic effect on slurry fluid loss control. It can be used to disperse weighted slurries up to 2250 kg/m³, but addition of this product to low-density slurries may result in a large excess of free water and particle segregation.

Excessive dispersant loading can lead to slurry disintegration, severely retarded set and possible bridging off mid-job. This is typical of cement
dispersants, and laboratory testing should be carried out before recommending for field use. CRM-22B is not recommended at temperatures exceeding 60°C.

Earth Pro Defoamer Powder is non-hazardous. Store in a cool dry place and away from incompatible materials. Earth Pro Defoamer Powder components may cause irritation to sensitive skin areas. Wear the appropriate safety goggles and protective equipment when handling this product.

Traditional

Appearance: Tan colored viscous liquid

Specific Gravity: 1.07-1.08

Flash Point: >93°C (closed cup)

Pour Point: -30°C

LTR is most often dry blended in cement. LTR should be stored in a dry place to prevent caking as a result of absorption of moisture. As with all organic materials, caution is advised when storing or handling near strong oxidizing agents such as chlorates, nitrates or peroxides. Avoid excess dust build up as contact with a spark or open flame could result in combustion or explosion. Use good industrial practice to avoid eye and excess skin contact. Wear a protective dust mask and goggles when handling and mixing.

Sodium Metasilicate

(%BWOC)

Slurry Density

(kg/m³)

Slurry Yield

(m³/ton)

Water

Compressive Strength,

24hr (kpa)

Thickening Time
(Hr:min)
(m³/ton) % 50 60
0.0 1893 0.929 0.537 44 32889 36613 +4:05 3:10 2:35 ---
0.15 1737 1.116 0.732 60 12039 15500 3:20 2:37 2:10 ---
1.0 1737 1.116 0.732 60 13073 14997 2:40 1:34 --- ---

0.25

1678 1.221 0.830 68 9791 10411 --- --- --- ---
1.0 1678 1.221 0.830 68 11308 11880 --- --- --- ---
0.5 1618 1.342 0.952 78 6523 8812 --- 3:30 2:10 ---
2.0 1618 1.342 0.952 78 9150 9791 1:53 1:28 --- ---
0.5 1558 1.488 1.100 90 5171 6392 --- --- --- ---
2.0 1558 1.488 1.100 90 827 7447 --- --- --- ---
0.75 1498 1.658 1.270 104 2634 4309 +5:00 +5:00 +5:00 +5:00
2.0 1498 1.658 1.270 104 4365 4502 +5:00 1:43 --- ---
1.0 1438 1.876 1.490 122 1827 2620 --- --- --- ---
2.0 1438 1.876 1.490 122 2896 3517 --- --- --- ---
1.5 1378 2.175 1.795 147 1014 1586 +5:00 +5:00 +5:00 +5:00
3.0 1378 2.175 1.795 147 1869 1993 +5:00 1:27 --- ---
2.0 1318 2.588 2.199 180 703 1207 --- --- --- ---
3.0 1318 2.588 2.199 180 1000 1414 --- --- --- ---

Microspheres are compatible with all classes of cement but must be dry blended and not premixed in the water. Use good industrial hygiene practice and wear goggles and a dust mask when handling the material.

Traditional

The table below details the approximate amount of Plug Sand required to fill one (1) vertical meter of casing or drill pipe:

Casing O.D. (mm) Plug Sand (kg required to fill 1 meter vertical)
139.7 19
177.8 32
219.1 52
222.3 49
244.5 64

Note: The weight of Plug Sand indicated in the above table is provided only as a guideline. Average casing weight was selected from typical oilfield tables for casing capacities, and may vary from your particular situation. To calculate the amount of Plug Sand required, the following formula can be used:

Amount of Sand Req (kg)= Casing Capacity (m³/meter) X 1650 kg/m³ (Bulk density of Plug Sand)

Salt mixes readily with water and can be mixed directly into the water.

Silica Fume (Undensified) is very stable and is not susceptible to fire, explosion or decomposition. The finely divided dust may cause eye and respiratory irritation. Use good industrial hygiene practice and wear goggles and a dust mask when handling the material.

Sodium Glucoheptonate is not hazardous. Avoid excessively humid conditions. Store in a cool dry place. Avoid inhalation or ingestion of product.

Stimpro 763 is a flammable liquid. Use good industrial safety procedures when handling this material.

The product is toxic and corrosive and requires special handling procedures. Refer to the Material Safety Data Sheet for handling instructions.

The product is toxic and requires special handling procedures. Refer to the Material Safety Data Sheet for handling instructions.

Quantities of Barite to be used and the volume increase may be quickly determined by dividing the desired weight by 2 to give the number of sacks required per 100 barrels of mud for each 0.1 ppg increase. For each 15 sacks added there will be one barrel volume increase. 

  • High viscosity for bit face evacuation and cuttings transport
  • Creates filter cake for wellbore stability
  • Exhibits gel strength for static cutting suspension
  • Increased lubrication to bit and tubulars over water alone
  • Inexpensive viscosifier for lost circulation situations
  • Easily clarified by flocculation and coagulation with appropriate additives

Placement of the Grout-Well products is best done using a positive displacement or progressive cavity pump. When pumping must be done with gear or diaphragm pumps, you may have to use additional make-up water to insure pumpability due to the limited pressure generated by these types of pumps.

When adding the grouts to make-up water, the slurry will resemble pancake batter, a creamy consistency with lumps. This is the ideal time to pump the fluid since all the bentonite has not fully hydrated. Once in place, the particles continue to swell, sealing off cracks and crevices while gelling to form its caulk-like consistency.

Provided local regulations allow, it is always recommended that the tremie line be withdrawn as the grout is being pumped. This permits the grout to continue its set undisturbed, reduces pump pressure, and minimizes unnecessary migration into surrounding formations.

Earth Pro Bio Bear Rod Grease can be applied like normal rod grease by hand swabbing it on. It is firmer in texture than traditional rod grease
products and requires a bit of technique change for application but field trials have shown that when applied properly this product has superior performance to its competitors.

Earth Pro Big Bear Rod Grease is recommended for grease lubrication on diamond drill rods whether operating on the surface or underground.

Kopr-Kote Drill Collar and Tool Joint Compound is recommended for use on rotary shouldered connections where downhole conditions are severe and the probability of makeup while drilling is anticipated. Typical applications would be steamed injection wells, geothermal applications, high angle holes, problem holes involving whip stocks, horizontal drilling applications, and on rigs powered by top-drive systems. Kopr-Kote prevents high stress levels which shorten the useful life of drill string connections.

Thermal Conductivity .93 Btu/hr-ft-OF 1.05 Btu/hr-ft-OF 1.13 Btu/hr-ft-OF 1.2 Btu/hr-ft-OF
Permeability <2 x 10-8  6 x 10-8 6 x 10-8; 6 x 10-8
Solids Content  64% 67% 69%  71%
Slurry Weight  13.6 lb/gal 14.4 lb/gal 15.1 lb/gal 15.2 lb/gal
Slurry Volume/Batch  29 gals 36 gals 41 gals 41.5 gals

 

Approximate Volumes for Grout
Drilled Hole Diameter Loop Inside Diameter Anlr. Volume (ft³/ft) Anlr. Volume (gal/ft)
4 3/4" 0.08 0.57
4.5 1" 0.09 0.70
5 1" 0.12 0.89
5.5 1" 0.15 1.10
6 1" 0.18 1.33
5 1-1/4" 0.11 0.84
5.5 1-1/4" 0.14 1.05
6 1-1/4" 0.17 1.29

  • Used in air rotary drilling (all disciplines) and underground tunneling
  • Non-flammable, non-toxic
  • Highly dispersible in water
  • Biodegradable

  • Full spectrum viscosifier
  • Optimal performance
  • Simple mixing and instructions

  • Lowers fluid loss
  • Promotes a very thin slick filter cake
  • Minimizes screen blinding due to short polymer length in comparison to synthetics
  • High shear mixing capability

  • High “low shear rate” viscosity for hole cleaning
  • Lubricates the drilling assembly
  • Exceptional rheology profile and inhibition on sensitive formations
  • Maximizes viscosity yield
  • Minimizes hydration times
  • Does not have a negative flocculating effect on bentonite systems
  • Less susceptible to salt or brackish water contamination
  • Easy, quick and even mixing

  • Maximize stability and usability
  • Hydrates in the formation not only in the wellbore
  • Complete solution for broken ground or loose over burden drilling

  • Stops lost circulation to formation by plugging fissures in rocks
  • Bonds loose rock together and prevents sloughing
  • Provides lubrication in loose, abrasive broken ground conditions
  • Resists alcohol bases and acids

  • Increases viscosity to provide hole cleaning and cutting transport
  • Shear thinning polymer to reduce pumping pressure demands
  • Maintains hole conditions in friable zones such as overburden, silts, sands and clays
  • Superior lubricating qualities eliminating vibration while increasing core recovery
  • Encapsulating structure reduces swelling of clays and caving shales

Linear

  • Viscosifier for all water based systems
  • Readily biodegradable product for use in environmentally sensitive situations
  • Not affected by ionic contaminants
  • Organic, non-toxic
  • Cools and lubricates bit
  • Non-toxic

  • Stop lost circulation to formation by plugging fissures in rock
  • Bond loose rock together end prevent sloughing
  • Provide lubrication in loose, abrasive broken ground conditions

  • Viscosifier for fresh and salt or brackish water sources
  • High “low shear rate” viscosity for hole cleaning
  • Functions as a 2 part system with DR-133 to offer exceptional rheology profile and inhibition on sensitive formations
  • Lubricates the drilling assembly

Pro-Yield is a dry polymer and should be added slowly through a high shear mixer to prevent lumps or fisheyes. Pro-Yield should not be added before bentonite, as the yielded Pro-Yield will prevent the bentonite from hydrating. It may be used in fresh, salt or hard water.

Product contains Methanol and as such is toxic and flammable. Avoid sparks and any sources of ignition.

Feedback received from mud engineers that have used this product include:

  • Easy to work as it dissolves easily
  • High performing fluid loss product
  • Exceeds performance of top brand products at lower concentrations
  • This product makes a night and day difference

As a flocculant Hyperdrill AD 855 can be added directly to the flow line, or it may be dispersed in water in the chemical barrel prior to adding to the flow line. Hyperdrill AD 855 is very slippery if spilled. A spill should be cleaned up with an absorbent material. (Do not add water to a spill).

Handling: Minimize skin contact. Wash with soap and water before eating, drinking, smoking, or using toilet facilities. Bags and containers of this material may be hazardous when emptied. Empty containers retain product residues.

Storage: prevent absorption of moisture and possible caking. Store in a cool, dry place. Do not store with cyanides, sulfides, chlorine, hypochlorous acid, hypochlorites or alkalis.

General Comments: Treat as a strong acid

Handling: The product is not considered dangerous and requires no special handling

Storage: Avoid contact with strong acids or alkaline-based products

Handling: Minimize skin contact. Wash with soap and water before eating, drinking, smoking, or using toilet facilities.

Storage: Keep in well ventilated area. Keep package tightly closed. Store above 32°F (0°C). Product should not be stored with or near strong caustic or oxidizing agents.

Modern

  • Non-plating, non-reactive and no gassing
  • Low sulfur content
  • Brushable over a wide temperature range
  • Sticks to wet joints
  • Consistent rig floor make-up
  • Resistant to further downhole make-up

Although Earth Pro pH Down Citric is of low hazard and toxicity, excess exposure to dust should be avoided to prevent irritation to the eyes, skin and respiratory tract.

As with all organic material, caution is advised when storing or handling near strong oxidizing agents, alkali metals or strong bases.

Recommended monovalent brine concentration is <20,000 mg/L TDS and multivalent ion concentration <2,000 mg/L TDS.

Earth Pro FR 100 has been formulated with an environmentally friendly surfactant package that ensures polymer hydration occurs almost instantaneously providing optimal performance. As a result, the product may be added as supplied on the fly by direct addition to the fracturing fluid.

Typical dosage is the range 0.25 – 2.0 L/m³.

Recommended monovalent brine concentration is <110,000 mg/L TDS and multivalent ion concentration >15,000 mg/L TDS.

Earth Pro FR 300 has been formulated with an environmentally friendly surfactant package that ensures polymer hydration occurs almost instantaneously providing optimal performance. As a result, the product may be added as supplied on the fly by direct addition to the fracturing fluid.

Typical dosage is the range 0.5 – 1.0 L/m³.

Product Number Product Name
27013 Mud Pump Liner 5.5” x 8”
46585 Mud Pump Liner 4.5” x 5” GD
46641 Mud Pump Liner 4” x 5”
42003 Liner Packaging 5.5” x 8”
42004 Liner Packaging 5” x 6”
42006 Liner 5” x 6” 5” Bore PPGD FG45650
42007 Liner 5.5” x 8” 5.5” Bore PPGD FD45655
44319 Gasket Liner 5” x 6” PPGD25G27
47338 Gasket Liner for D-300 AJ1125
47339 Gasket Liner for D-300 AJ1115
47225 Chrome Liner 5.5” x 8” and 5.5” x 10” PPGD FD45655C

 

Product Number Size
38449 3” x 6”
49561 4” x 6”
30651 4” x 7”
38450 4” x 7”
46446 4” x 7”
46135 4.5” x 6”           
30650 4.5” x 8”
38451 5” x 8”
49172 5.75” x 8”
31036 6” x 9”
38452 6” x 10”
46341 8”
38442 8” x 14”

Product Number Description
49011 4.5" 5TPI Female X 3" NPT Female
49010 4.5" 5TPI Female X 4" NPT Female
49006 4.94" Female Slip X 4" NPT Female
48962 4.94" 5TPI Female X 3" NPT Female
49005 4.94" 5TPI Female X 4" NPT Female
49167 5" LH 5TPI Female X 3" NPT Female
49166 5" LH 5TPI Female X 4" NPT Female
49165 5" LH 5TPI Female X 5" NPT Female
49164 6" LH 5TPI Female X 4" NPT Female
49009 6" LH 5TPI Female X 5" NPT Female
49007 6" RH 5TPI Female X 4" NPT Female
49008 6" RH 5TPI Female X 5" NPT Female

Product Number TEL x Length Slot Size
49523V 4” x 5’ .008”
41195V 4” x 5’ .010”
41196V 4” x 5’ .012”
41198V 4” x 5’ .020”
41268V 4” x 5’ .030”
41236V 5” x 10’ .007”
41238V 5” x 10’ .015”
46091V 5” x 5’ .008”
41199V 5” x 5’ .010”
41201V 5” x 5’ .015”
41202V 5” x 5’ .020”
41203V 5” x 5’ .025”
41204V 6” x 5’ .010”
41205V 6” x 5’ .012”
41206V 6” x 5’ .015”
41207V 6” x 5’ .020”
42320V 6” x 5’ .025”
41386V 6” x 5’ .030”
41383V 6” x 5’ .040”
41395V 6” x 5’ .050”

Product Number Product Name Packaging
47252 Silica Sand 10/20 50lb
47255 Silica Sand 20/40 50lb
19460/28111 Silica Sand 50/100 40kg/88lb
28113 Silica Abras. Sand 30/50 88lb
30122 Silica Sand #16 80lb
99900466 Silica Sand, LM #50 50lb
99900467 Silica Sand, LM #20/30 50lb

Product Number Size Schedule Description
46429 1" x 20' 120 SHUR-ALIGN MPT x FPT
49107 1-1/2” x 20’ 120 SHUR-ALIGN MPT x FPT
47021 1-1/4” x 20’ 120 SHUR-ALIGN MPT x FPT
46858 2” x 20’ 120 SHUR-ALIGN MPT x FPT

Product Number Size Wall Thickness End Type
41724 4-1/2" x 21' .237" Thread & Coupled
41735 5-9/16" x 20' .188" Inserted Joint
41736 5-9/16" x 20' .258" Inserted Joint
41165 6-5/8" x 5' .188" Plain End
47139 6-5/8" x 20' .188" Bevelled
41746 6-5/8" x 20' .188" Inserted Joint
41751 7" x 20' .231" Inserted Joint
41759 8-5/8" x 21' .322" Thread & Coupled
46778 10-3/4" x 21' .365" Thread & Coupled

Product Number Size Style
41850 2" x 2-7/8" OD Weld On
44101 4-1/2" x 4" ID x 4" Long Weld On
46684 4-1/2" x 4" ID x 4" Long Threaded
41853 4-1/2" x 4-1/8" ID x 4" Long Weld On
41851 4-1/2" x 4-2/25" ID x 4" Long Threaded
43949 5-9/16" x 5-1/4" ID x 4" Long Threaded
43457 5-9/16" x 5-1/4" ID x 4" Long Weld On
41872 5-9/16" x 5-1/4" ID x 4-1/2" Long Weld On
41903 6-5/8" x 6-1/8" ID x 4" Long Weld On
41900 6-5/8" x 6-1/8" ID x 4" Long Threaded
41890 6-5/8" x 6-1/8" ID x 4-1/2" Long Threaded
41899 6-5/8" x 6-1/8" ID x 5-3/8" Long Threaded
41878 6-5/8" x 6-1/8" ID x 5-3/8" Long Weld On
41916 6-5/8" x 6-1/4" ID x 3-1/2" Long Weld On
41918 6-5/8" x 6-1/4" ID x 4-1/2" Long Threaded
41920 6-5/8" x 6-1/4" ID x 4-1/2" Long Weld On
43479 6-5/8" x 6-1/4" ID x 5-1/2" Long Weld On
43458 6-5/8" x 6-1/4" ID x 5-3/8" Long Weld On
41896 6-5/8" x 6-1/4" ID x 5-3/8" Long Threaded
41893 6-5/8" x 6-1/4" ID x 5-3/8" Long Threaded
41923 7" x 6-1/2" ID x 5-3/4" Long Weld On
43468 8-5/8" x 8-1/8" ID x 7-3/4" Long Weld On
44569 8-5/8" x 8-1/8" ID x 7-3/4" Long Threaded
41928 8-5/8" x 8-1/4" ID x 7-3/4" Long Weld On
43469 10-3/4" x 10-1/4" ID x 9-1/2" Long Weld On

Size Schedule Length Finish
4" 40 10.5" galvanized or black
6" 40 10.5" galvanized or black
8" 40 10.5" galvanized or black
10" 40 10.5" galvanized or black
12" 40 10.5" galvanized or black

Product Number Product Description
47098 QC Slope Indicator Casing 70 mm x 3 m (2.75” x 10’)
48901 QC Slope Indicator Casing 85 mm x 3 m (3.34” x 10’)
48908 QC Slope Indicator Casing 85 mm x 1.5 m (3.34” x 5’)
49020 QC Slope Indicator Casing 70 mm x 1.5 m (2.75” x 5’)

Product Number Size TPI Description
41081 2” x 5’ 2 .020” Slotted
41102 2” x 5’ 2 .010” Slotted
41183 2” x 5’ 4  
41184 2” x 5’ 4 .020” Slotted
41082 2” x 10’ 2 .010” Slotted
41083 2” x 10’ 2 .020” Slotted
41103 2” x 10’ 2  
41182 2” x 10’ 4 .020” Slotted
46154 4” x 10’ 8  
46155 4” x 10’ 8 .020” Slotted
41343 5” x 20’ 8  

Product Number Size Description
37814 3.5” x 10” Manhole Cover CI Water Tight
46420 4” x 7” Manhole Cover Cast Iron
41385 6” Manhole Heavy Skirt
47103 6” Monitoring Well Manhole Lid and Ring Only #6SLW
37815 6” x 6” Manhole Cover Aluminum
41224 6” x 10” Manhole
36601 7” x 10” Manhole EMI Painted
41217 7” x 10” Manhole EMI
37807 7” x 10” Manhole Cover
36602 8” x 8” Manhole EMI Painted
46561 8” x 8” Manhole Cover
37808 8” x 12” Manhole Cover
41961 8” x 12” Manhole
37812 9” Manhole Cover MI 519 Load 39000 Heavy Duty Water Tight
37809 9” x 12” Manhole Cover
37810 12” x 12” Manhole Cover
39739 18” Manhole Lid
37811 18” x 12” Manhole Cover
39740 18” x 18” Manhole Cover
46519 18” x 18” Manhole Lid Only

Product Number

Size

Description

37740

6.25” x 1 x 2.75”

 

37741

4” x 1”

 

37742

5” x 1”

 

38486

4” x 1” x 2.75”

 

38488

5” x 1” x 1.25”

 

38494

6.25” x 1”

 

38496

6.25” x 2”

Single Hole

42602

2” x 1”

Clamp over well

42609

8”

Single Hole

42610

8”

Single Hole

42611

8”

Single Hole

42612

5” x 1.5”

 

42613

6” x 1.25”

 

46614

10” x 3”

Single Hole

47377

12” x 2”

Single Hole

47387

4” x 1.25”

 

The Hydrolift-2 is an electrically powered automatic actuator for use with the Standard Flow, High Flow and Low Flow Inertial pumping systems.

The Hydrolift-2 is fully adjustable and will adapt to almost any size casing or protective well casing and can also be used with flush grade well completions. The Hydrolift-2 supports the inertial pump tubing and also anchors the discharge end of the tubing facilitating sample collection.

The Hydrolift-2 requires either a 110 volt or 220 volt AC power supply. Using the Hydrolift-2 will result in a big boost to your field sampling program. This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 150 to 200 feet deep.

This actuator is also great for use when developing monitoring wells. The use of an automated actuator will eliminate the fatigue that can be experienced on large monitoring programs.

  • fully adjustable
  • hinged tubing clamp
  • suitable for use with Standard FlowHigh Flow and Low Flow Inertial Pumps
  • adapts to almost any size casing or protective well casing
  • anchored discharge end of tubing facilitates sample collection
  • reduces fatigue when purging large volumes from wells

The PowerPack PP1 is a gasoline powered automatic actuator for use with the Standard Flow System, High Flow System and Low Flow Inertial Pumping systems.

The PowerPack PP1 is fully adjustable and will adapt to almost any size casing or protective well casing and can also be used with flush grade well completions. The PowerPack PP1 supports the inertial pump tubing and also anchors the discharge end of the tubing facilitating sample collection.

The PowerPack PP1 is powered by the Honda GX25 a 25cc Mini 4-Stroke OHC gasoline engine. This lightweight motor is EPA/CARB compliant, runs on regular gas and has a quiet - pleasing "low" tone. The PowerPack PP1 includes a backpack frame making it completely portable. Using the PowerPack PP1 will result in a big boost to your field sampling program. 

This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 150-200 feet deep. This actuator is also great for use when developing monitoring wells.

The use of an automated actuator will eliminate the fatigue that can be experienced on large monitoring programs.

  • fully adjustable
  • powered by Honda GX25 a 25cc Mini 4-Stroke OHC gasoline engine
  • includes backpack frame for complete portability
  • suitable for use with Standard Flow, High Flow & Low Flow Inertial Pumps
  • adapts to almost any size casing or protective well casing
  • anchored discharge end of tubing facilitates sample collection
  • reduces fatigue when purging large volumes from wells

The PowerPump 2 is a gasoline powered automatic actuator for use with the Standard Flow System, High Flow System and Low Flow Inertial Pumping systems.

The PowerPump 2 is adjustable and will adapt to almost any size casing of protective well casing and can also be used with flush grade well completions. The PowerPump 2 supports the inertial pump tubing and also anchors the discharge end of the tubing, facilitating sample collection.

The PowerPump 2 is powered by the Honda GX100 Air-cooled, 4-Stroke, OHC gasoline engine. This 2.8 hp motor is EPA/CARB compliant, runs on regular gas. The PowerPump 2 is our most powerful actuator and can operate the High Flow inertial pump in monitoring wells to depths of up to 300 feet. Using the PowerPump 2 will result in a big boost to your field sampling program, especially at sites with very deep installations.

This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 300 feet deep. This actuator is also great for use when developing monitoring wells.

The use of an automated actuator will eliminate the fatigue that can be experienced on large monitoring programs.

  • fully adjustable
  • powered by Honda GX100 Air-cooled, 4-Stroke, OHC gasoline engine
  • our most powerful actuator
  • suitable for use with Standard Flow, High Flow& Low Flow Inertial Pumps
  • adapts to almost any size casing or protective well casing
  • anchored discharge end of tubing facilitates sample collection
  • reduces fatigue when purging large volumes from wells

The Low Flow System is probably most frequently operated by hand, although the Hydrolift-2 and a Lever Pump can also be used to operate this system.

The Standard Flow System can be manually operated in most wells simply by holding the tubing by hand and oscillating it up and down in the well. Sometimes performance and endurance can be improved with the addition of a Lever Pump

The greatest performance improvements are realized with the use of the Hydrolift-2, PowerPack PP1 or PowerPump-2. The use of one of these automated actuators greatly improves the well development capacity of the inertial pump. The automated actuators are also recommended when substantial purge volumes are required.

EcoBailers are made of clear virgin PVC with a density of 1.31 whereas most disposable bailers are made of polyethylene which has a specific gravity of 0.96 to 0.98. PVC is also transparent whereas polyethylene is translucent, because of this, when you use the EcoBailer you can inspect your sample while it's still in the bailer. 

Clear PVC EcoBailers are easily adapted to the FHT-45 Disposable Groundwater Filter for collection of samples for metals analysis directly from the bailer. A short length of 1/4" OD or 1/2” OD LDPE tubing along with the bottom emptying spout can be used to easily connect the FHT-45 or FMT-45 inline disposable groundwater filter to the bailer. This allows the bailed sample to flow by gravity directly through the filter and into a sample container. In many cases a 1 liter sample can be filtered in under 2 minutes using this method.

These bailers are designed with a special valve and valve seat to provide more positive sealing and less clogging when removing the bailer from the well. All bailers come with the handy bottom emptying spout. It assists in collecting non-aerated samples from the valve end of the bailer, which is ideal for VOC sample collection.

  • available in 1.5" diameter x 3' length, 1027 mL volume 
  • longer valves to prevent silt entry and leakage
  • easy pour tops to facilitate the sampling process
  • custom molded emptying devices that allow control of sample flow

  • No-purge device provides comparable, formation quality samples of ALL parameters from 3" and larger wells for both short and long-term monitoring
  • Disposable
  • Fits in 3" Schedule 40 and larger wells
  • Standard material = virgin 4 mil PE. Tensile strength 25-35 lb
  • Absolute maximum volume obtainable without spilling 1.68 liters
  • Layflat = 4"W x 30"L
  • Filled Diameter = 2.6"
  • Filled Volume = ~1600 mL
  • Fill Stroke = 30"

Traditional

Product Number Size Description
37784 4.5” Aluminum Locking Well Cap
37785 5-5/8” Aluminum Locking Well Cap
37786 6-5/8” Aluminum Locking Well Cap
49505 6-5/8” Aluminum Locking Vented with 1” Conduit Neck Well Cap
47257 7" Aluminum Locking Well Cap – No Conduit Neck

The CAP300X2 features 300 square centimeters of the same, high quality PES media as our other filters, providing a fast, efficient and economical option for specialized filtering requirements.

All Inline Disposable Micron Filters are pre-rinsed with one liter of de-ionized water to ensure purity, and are now certified to rinse clean. Independent ICP/MS analysis proves it.

Product Number Description
30667 Displacement Plug HQ Grind Finish to 2-18/25” x 4-1/8”
30668 Displacement Plug HWL
30669 Displacement Plug NWL
30670 Displacement Plug BWL
30671 Displacement Plug AQ
30672 Displacement Plug NTW
30673 Displacement Plug PQ 4-1/2”
30675 Displacement Plug PW 5-1/2”
30679 Displacement Plug 7” Top
30680 Displacement Plug 8-1/16” Top

  • Left or right hand pipe thread
  • Wedges
  • Rubber seal
  • Aluminum tube
  • Plastic check ball 

Product Number Plug Size Hole Size
36837 0.94” x 72” 1”
30171 1.125” x 36” 1.25”
30172 1.125” x 48” 1.25”
36999 1.125” x 12” 1.25”
37000 1.125” x 18” 1.25”
37001 1.125” x 24” 1.25”
37002 1.125” x 60” 1.25”
37003 1.125” x 72” 1.25”
37004 1.125” x 96” 1.25”
37005 1.125” x 120” 1.25”
39597 1.125” x 6” 1.25”
30173 1.25” x 48” 1.375”
37006 1.25” x 12” 1.375”
37007 1.25” x 18” 1.375”
37008 1.25” x 24” 1.375”
37009 1.25” x 36” 1.375”
37010 1.25” x 60” 1.375”
37011 1.25” x 72” 1.375”
37012 1.25” x 96” 1.375”
37013 1.25” x 120” 1.375”
30174 1.375” x 36” 1.5”
37014 1.375” x 12” 1.5”
37015 1.375” x 18” 1.5”
37016 1.375” x 24” 1.5”
37017 1.375” x 48” 1.5”
37018 1.375” x 60” 1.5”
37019 1.375” x 72” 1.5”
37020 1.375” x 96” 1.5”
37021 1.375” x 120” 1.5”
30175 1.625” x 18” 1.75”
30176 1.625” x 36” 1.75”
30177 1.625” x 48” 1.75”
30178 1.625” x 72” 1.75”
37022 1.625” x 12” 1.75”
37023 1.625” x 24” 1.75”
37024 1.625” x 60” 1.75”
37025 1.625” x 96” 1.75”
37026 1.625” x 120” 1.75”
39554 1.625” x 144” 1.75”
30179 1.75” x 36” 1.875”
30180 1.75” x 48” 1.875”
37027 1.75” x 12” 1.875”
37028 1.75” x 18” 1.875”
37029 1.75” x 24” 1.875”
37030 1.75” x 60” 1.875”
37031 1.75” x 72” 1.875”
37032 1.75” x 96” 1.875”
37033 1.75” x 120” 1.875”
39546 1.75” x 144” 1.875”
39547 1.75” x 120” 1.875”
30181 1.875” x 36” 2”
30182 1.875” x 48” 2”
30183 1.875” x 72” 2”
30184 1.875” x 96” 2”
37034 1.875” x 12” 2”
37035 1.875” x 18” 2”
37036 1.875” x 24” 2”
37037 1.875” x 60” 2”
37038 1.875” x 120” 2”
30193 2.125” x 48” 2.25”
37040 2.125” x 18” 2.25”
37041 2.125” x 24” 2.25”
37042 2.125” x 36” 2.25”
37043 2.125” x 60” 2.25”
37044 2.125” x 72” 2.25”
37045 2.125” x 96” 2.25”
37046 2.125” x 120” 2.25”
30194 2.25” x 36” 2.375”
30195 2.25” x 48” 2.375”
30196 2.25” x 60” 2.375”
30197 2.25” x 72” 2.375”
30198 2.25” x 96” 2.375”
37047 2.25” x 12” 2.375”
37048 2.25” x 18” 2.375”
37049 2.25” x 24” 2.375”
37050 2.25” x 120” 2.375”
39135 2.25” x 240” 2.375”
30199 2.375” x 12” 2.5”
30201 2.375” x 36” 2.5”
30202 2.375” x 48” 2.5”
30203 2.375” x 72” 2.5”
37051 2.375” x 18” 2.5”
37052 2.375” x 24” 2.5”
37053 2.375” x 60” 2.5”
37054 2.375” x 96” 2.5”
37055 2.375” x 120” 2.5”
37039 2.625” x 12” 2.75”
39530 2.625” x 48” 2.75”
30204 2.875” x 36” 3”
30205 2.875” x 48” 3”
30206 2.875” x 72” 3”
30207 2.875” x 96” 3”
37056 2.875” x 12” 3”
37057 2.875” x 18” 3”
37058 2.875” x 24” 3”
37059 2.875” x 60” 3”
37060 2.875” x 120” 3”
39099 3.375” x 36” 3.5”
39382 3.375” x 48” 3.5”
39221 3.875” x 72” 4”
39369 3.875” x 60” 4”
39456 3.875” x 48” 4”
39639 3.875” x 36” 4”

  • Excellent biodegradability (>60% by DOC Method) essentially non-toxic
  • Non-oil wetting
  • Non-foaming
  • Multiple absorption sites
  • The normal concentration used in the field is 3-5 L/m³

Part Number Description
102109 / 102117 BWL 3 m (10 ft)
102125 / 102133 BWL 1.5 m (5 ft)
102110 / 102118 NWL 3 m (10 ft)
102126 / 102134 NWL 1.5 m (5 ft)
102111 / 102119 HWL 3 m (10 ft)
102127 / 102135 HWL 1.5 m (5 ft)

Part Number Metric Length Imperial Length
102073 / 102072 3 m 10 ft
102071 / 102070 1.5 m 5 ft
103298 / 103297 0.6 m 2 ft

Part Number Size Metric Length Imperial Length
102081 / 102080 HW 3 m 10 ft
102079 / 102078 HW 1.5 m 5 ft
102907 / 102372 HW 0.6 m 2 ft
102089 / 102088 HWT 3 m 10 ft
102087 / 102086 HWT 1.5 m 5 ft
102963 / 102328 HWT 0.6 m 2 ft

Product Number Description
44104 J Plug 1" Locking Sch 40 
44106 J Plug 1-1/2" Locking Sch 40/80
37939 J Plug 2" Locking Sch 40
46567 J Plug 2" Locking Sch 80
47369 J Plug 4" Locking Sch 40
48812 J Plug 4" Locking Sch 80

  • Model 900 Viscometer is a true Couette coaxial cylinder rotational viscometer
  • Run multiple units on one computer
  • Push button calibration history and graphs available for improved analysis (with ORCADA software)
  • Single button operations on the keypad
  • Routine repairs are easily performed
  • Has the ability to operate accurately at extremely low shear rates (0.01 RPM)
  • Not necessary to stop the motor between speed changes

  • Ultimate in portability
  • Proven test procedures
  • Reliability
  • Small footprint if used in laboratory
  • Accurate, tamper proof temperature controller

** Not recommended for testing cuttings **

Traditional

  • Rugged, stainless steel carrying case
  • Electronic temperature control
  • Improves accuracy and readability
  • Digital display
  • Provides better reproducibility
  • Ultimate in portability
  • Small footprint if used in laboratory
  • Accurate, tamper proof temperature controller
  • Includes all accessories necessary to run a test

** Recommended for testing cuttings **

  • Extremely portable
  • May be operated by filtering upwards, which negate cutting settling on the filter meduim prior to testing
  • Easily obtainable CO2 Bulbs provide pressure
  • Proven design for over 50 years of successful usage
  • Easy to service and obtain replacement parts

  • Stainless steel test cell
  • Built-in pressure regulator
  • Suitable for field and lab use
  • Conforms to API specifications

  • Durability: The machined stainless steel construction is stronger, less susceptible to corrosion, and more consistent from unit to unit.
  • Ease of Use: The smooth finish is easy to clean and the laseretched scales are clear and easy to read. The more consistent construction makes calibration easier.

  • Equipped with a digital readout for higher accuracy
  • LCD display makes measurements easy to read
  • Built-in calibration tests make calibrations simple
  • Automatic NaCl Measurements - no longer have to manually use a nomograph
  • Lucite® Cell - transparent and removable, making it easy to clean

Linear

  • Maximum Speed: 23,000 RPM
  • 115-Volt, 60 Hz, or 230-Volt, 50 Hz
  • Each can be operated via a 1.25 KVA power supply
  • Size: 45” × 32” × 12” (114 × 81 × 31 cm)
  • Weight: 75 lb (34.1 kg)
  • Crated Size: 45” × 32” × 12” (114 × 81 × 31 cm)
  • Crated Weight: Approximately 215 lb (97.6 kg
  • Two preset mixing speeds and variable speed (For Cement: 4,000 and 12,000 RPM, For Fracturing Fluids: 500 and 1,000 RPM)
  • Mixing Container (For Cement: Stainless Steel, 1 Liter - For Fracturing Fluids: Glass, 1 Liter)

  • Automatically conditions the slurry in-place (1 - 150 RPM)
  • Provides a direct mechanical measurement of static gel strength
  • Simultaneously measures static gel strength and compressive strength (dual-cell units only)
  • Intermittent or continuous measurement under high-temperature, high-pressure conditions
  • Data acquisition system with automatic temperature control included
  • Simple calibration and system check
  • Quick clean up and turn around

  • Maximum Pressure: 16,000 PSI (110.3 MPa)
  • Maximum Temperature: 400°F (204.4°C)
  • Temperature Controller: Digital PID 1° Resolution
  • Internal Heater: 2,500 Watt (5,000 Watt Available)
  • Slurry Cup: 150 RPM Rotational Speed; 316 Stainless Steel
  • 220 Volt, 50/60 Hz, 25 Amp electrical power supply
  • Size: 25 × 16 × 20 inches (63.5 × 40.6 × 50.8 cm)
  • Weight: Approximately 215 lb (97.6 kg)

Linear

A cement specimen is placed into a sleeve which is then inserted into the Modified Hassler style test cell. Nitrogen is displaced through the cement at various flow rates to determine the permeability.

  • Windows based, Computerized Data Acquisition and Control system: provides detailed test information, precise control, and allows cylindrical and cube-shaped samples
  • Small foot-print: saves valuable lab space and increases efficiency with quick and easy clean up
  • Safety minded: clamshell head design and safety switches protect people and equipment from possible debris during operation
  • Prevents over pressure: a safety head, rupture disk, and high-pressure alarm assembly
  • Proppant Testing: can test proppant according to API Recommended Practice 19°C
  • Self-Aligning platens: easier to load samples and allows for equal force to be applied
  • Communication: operates in standalone or with computer control via RS-232 or Ethernet connections
  • Loading Rates: variable load rate and constant load testing

Traditional

OSKOverpack Spill Kit (approx. absorption capacity = 231 liters/51 gallons): 

  • 100 - sorbent pads
  • 6 - small pillows
  • 2 - large pillows
  • 5 - large socks
  • 2 - small socks
  • 1 - 25 lb. bag granular absorbent
  • 1 - plug pattie (instant stop leak)
  • 1 - neoprene drain cover
  • 2 - disposal bags
  • 2 - pair splash goggles
  • 2 - pair reusable nitrile gloves
  • 2 - poly-coated Tyvek coverall
  • 1 - 95 gal overpack (DOT/UN rated)

Sodium Metasilicate (%BWOC) Slurry Density (kg/m³) Slurry Yield (m³/ton) Water Compressive Strength, 24 hr (kpa) Thickening Time (hr:min)
m³/ton % 50 60
0 1893 0.929 0.537 44 32889 36613 +4:05 3:10 2:35 ---
0.15 1737 1.116 0.732 60 12039 15500 3:20 2:37 2:10 ---
1.0 1737 1.116 0.732 60 13073 14997 2:40 1:34 --- ---
0.25 1678 1.221 0.830 68 9791 10411 --- --- --- ---
1.0 1678 1.221 0.830 68 11308 11880 --- --- --- ---
0.5 1618 1.342 0.952 78 6523 8812 --- 3:30 2:10 ---
2.0 1618 1.342 0.952 78 9150 9791 1:53 1:28 --- ---
0.5 1558 1.488 1.100 90 5171 6392 --- --- --- ---
2.0 1558 1.488 1.100 90 827 7447 --- --- --- ---
0.75 1498 1.658 1.270 104 2634 4309 +5:00 +5:00 +5:00 +5:00
2.0 1498 1.658 1.270 104 4365 4502 +5:00 1:43 --- ---
1.0 1438 1.876 1.490 122 1827 2620 --- --- --- ---
2.0 1438 1.876 1.490 122 2896 3517 --- --- --- ---
1.5 1378 2.175 1.795 147 1014 1586 +5:00 +5:00 +5:00 +5:00
3.0 1378 2.175 1.795 147 1869 1993 +5:00 1:27 --- ---
2.0 1318 2.588 2.199 180 703 1207 --- --- --- ---
3.0 1318 2.588 2.199 180 1000 1414 --- --- --- ---

This product mixes easily in cold water with moderate agitation. Sodium Silicate is corrosive. Wear the appropriate safety goggles and protective equipment when handling this product.

Silica Flour is very stable and is not susceptible to fire, explosion or decomposition. The finely divided dust may cause eye and respiratory irritation. Use good industrial hygiene practice and wear goggles and a dust mask when handling the material. 

Dry Grout Water Usable Slurry Solids Content
50lb 14 gal 17 gal 30.0%
50lb 15 gal 18 gal 28.6%
50lb 16 gal 19 gal 27.3%

Dry Driven Casing: In cable tool operations, these granular Enviroplug No.16 can be used to grout the casing as it is being driven. A hole should be dug at the surface 6 to 8 inches larger than casing and 12 to 14 inches deep. Once the driving has begun, fill this hole with Enviroplug No.16. The granules will follow the drive shoe downward as driving continues creating a bentonite collar around the casing.

Pumpable Grout Seals: Enviroplug No.16 can be used in a pumpable slurry mix to grout wells or abandon holes. Agitate until the polymer is dispersed, then add 50 pounds of Enviroplug No.16. Pump immediately.

CAUTION: Continued agitation will result in extreme viscosity and become unpumpable.

Cased Holes or Uncased Holes: For decommissioning cased or uncased holes larger than 3" diameter, Enviroplug Coarse can be used. If static water is present, pour chips from the bag at a rate of 1 1/2 to 2 minutes per 50 pounds. A funneling device with a 2" opening can be used to insure a constant flow of material into the hole. Should the water level be quite low - a screen can be used to drop out "fines" from the material before entering the hole. 

Abandoning Dug Wells: Completely filling dug wells with bentonite chips can be very expensive and unnecessary. To economically decommission and stabilize dug wells, Enviroplug Coarse should be placed from the bottom section upward to 3 feet above the water bearing zone. Alternate sections of sand, fine gravel, or clay upward with a 12" layer of Enviroplug Coarse every 5 to 6 feet. Any of the above methods should be finished off approximately 3 feet below the surface, then filled with native soil or cement depending upon local regulatory requirements.

Seismic Shot Holes: After the hole is drilled and charge is placed, pour Enviroplug Coarse slowly into the hole (1½ - 2 minutes per bag). In wet hole conditions add enough Enviroplug Coarse to fill up to the static water level. In a dry hole, add 2 to 4 bags directly over the charge. Where auger drills are used or where water is injected, pour 2 bags per 50 feet of hole depth.

Linear

Standard safety equipment should be worn when handling this product. For further handling and safety instructions consult Material Safety Data Sheet.

Losing the fluid phase of a slurry into the soil can compromise the integrity of the formations. This can allow materials to fall in against the segments, increasing drag and elevating jacking pressures. Micro-Gel slurries protect against excessive fluid loss by laying down a thin tough filter cake that limits the water phase influence on surrounding formations. Traditionally used slurries demonstrate fluid loss values nearly twice the level of Micro-Gel.

Part Number Length Description
30682 5' H3 Kleer-Kore Tube
30683 5' N3 Kleer-Kore Tube
39595 5' P3 Kleer-Kore Tube
39163 10' N3 Kleer-Kore Tube
39214 10' H3 Kleer-Kore Tube
39631 10' P3 Kleer-Kore Tube

Traditional

Super-Sweep Fiber is added to a variety of drilling fluids to increase the flow and removal of solids within a well-bore application. Super-Sweep Fiber suspends easily and uniformly in fresh water, salt water, water-based drilling muds, allowing it to effectively transport solids out of the drilling environment. Super-Sweep Fiber does not affect the chemistry nor increase the viscosity of the drilling fluid.

Graphite Powder is added to the mud system through the mud-mixing hopper. Because it is extremely fine, it is recommended that a dust mask and goggles be worn while the graphite is being mixed. 

Note: Graphite Powder will have the same effect as ball bearings on any hard surface.  Post warning signs if spilled and sweep up immediately.

Modern

Part Number Description Hoisting Weight
100669 AW Rod Pin to BWL Rod Pin 5,000 LB
100671 NW Rod Pin to BWL Rod Pin 10,000/30,000 LB
102571 NW Rod Pin to BWL Bullnose 10,000/30,000 LB

Part Number Description
102575 BWL Rod Box to BW Casing Pin

Part Number Description
102579 BWL Water Saver Sub

Part Number Description Crown Waterway Configuration
103246 N Carbonado W Wide Waterway
103548 N Carbonado Tapered Wide Waterway

Part Number Description
101016 BW Level 1 Casing Shoe
101006 BW Level 2 Casing Shoe
103827 BW Carbonado Casing Shoe

Linear

Part Number Description
102274 NWL (T11) Rod Shoe 
102663 NWL (T12) Rod Shoe

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
100738 Core Barrel Assembly, 3 m (10 ft) -
100699 Core Barrel Assembly, 1.5 m (5 ft) -
100768 Locking Coupling, Conventional, Tang
100735 Adaptor Coupling
100737 Landing Ring 1
100726 Outer Tube, 3 m (10 ft) 1
100758 Outer Tube, 1.5 m (5 ft) -
100734 Inner Tube Stabilizer 1
100700 Head Assembly 1
100725 Inner Tube, 3 m (10 ft) 1
100757 Inner Tube, 1.5 m (5 ft) -
100730 Stop Ring 1
100731 Core Lifter, Slotted 1
100733 Core Lifter Case 1

 

Options
Part Number Description
100739 Locking Coupling, Conventional, No Tang
100736 Locking Coupling, Full Hole, Tang
100763 Locking Coupling, Full Hole, No Tang
100732 Core Lifter, Fluted
101566 Core Lifter, Smooth
101623 Core Lifter, Slotted, Diamond Coated
101624 Core Lifter, Fluted, Diamond Coated
100776 Outer Tube 3 m (10 ft) C/P
100775 Outer Tube 1.5 m (5 ft) C/P
100761 Inner Tube 3 m (10 ft) C/P
100760 Inner Tube 1.5 m (5 ft) C/P
100644 Core Barrel Plug

Conversion Kit
Part Number Description Qty
101423 Link-Latch to Edge Latch Conversion Kit -
100715 Latch 2
100722 Latch Spring 1
100701 Latch Retracting Pin 2
100702 Latch Pivot Pin 1
100874 Drift Pin Tool 1
101427 Conversion Instructions 1
101152 Parts Pouch 1

To simplify the conversion of your current core barrel systems to the Edge Latch system, Di-Corp offers a conversion assembly which can be attached to the spindle of most systems.

Conversion Head Assembly
Part Number Description Qty
101959 Core Barrel Conversion Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Coiled Spring Pin, ø7/16" x 1" Long 1
100712 Spearhead Base 1
100701 Latch Retracting Pin 2
100713 Latch Retracting Case 1
100714 Latch Body, Upper 1
100702 Latch Pivot Pin 1
100722 Latch Spring 1
100715 Latch 2
100716 Landing Shoulder 1
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 1
100717 Latch Body, Lower 1
100703 Lock Washer 1

Inner Tube Cap Assembly without Thread Protector
Part Number Description Qty
100721 Inner Tube Cap Assembly without Thread Protector -
100720 Inner Tube Cap Body 1
100461 Grease Fitting 1
100724 Stainless Steel Ball, 3/4" 1
100723 Check Valve Body 1

 

Inner Tube Cap Assembly with Thread Protector
Part Number Description Qty
101821 Inner Tube Cap Assembly with Thread Protector -
100720 Inner Tube Cap Body 1
100461 Grease Fitting 1
100724 Stainless Steel Ball, 3/4" 1
100723 Check Valve Body 1
100639 Thread Protector, Inner Tube Cap 1

If drilling in ground conditions where the loss of costly drilling fluids becomes a problem, it may be necessary to replace the Landing Indication components with optional Fluid Retention parts which act like a check valve to maintain a column of fluid in the drill string.

Fluid Retention Kit
Part Number Description Qty
100611 Fluid Retention Kit -
100452 Stainless Steel Ball, ø22mm 1
100612 Bushing, Fluid Retention 1
101138 Bushing, Heavy Mud Fluid Retention 1
100630 Fluid Retention Compression Spring, Light 1
100634 Fluid Retention Compression Spring, Medium  1

Part Number Description
100708 Inner Tube Coupling
100762 Inner Tube Extension, Stabilized (10") Reaming Shell
101810 Inner Tube Extension, Double Stabilized (18") Reaming Shell

Part Number Description Qty
102900 Overshot Assembly, Rolling -
101809 Overshot Head Assembly -
102899 Upper Overshot, Rolling 1
101165 Overshot Head Body 1
100533 Set Screw, 3/8" UNF x 3/4" NYLOK 1
100888 Compression Spring, Lifting Dog 1
100889 Lifting Dog 2
101166 Lifting Dog Pivot Pin 1
101167 Upper Sway Pin 1
101558 Spring Pin, 3/16" x 1-3/8" 1
101168 Pin Lock 2
100539 Self Locking Cap Screw 4
100692 Overshot Loading Fork Tool 1
100774 Overshot Loading Funnel 1

Product Number Product Name Packaging
19642 Well Sand #0 50lb
19643 Well Sand #1 50lb
19644 Well Sand #2 50lb
19645 Well Sand #3 50lb

Traditional

Optimal treatment concentration will vary depending on the specific application. 

Earth Pro Bitu-Seal is typically used in the concentrations ranging from 10 to 30 kg/m3 and is added directly to the mud system. Avoid breathing dust.

Consult the MSDS, safety posters, and/or product label before use, and use personal protective equipment as advised.

Under normal conditions, for a program with a corrosion level of ≥ 25 mpy, initially add 5 L/m³ Earth Pro Brine-Cor. Severe corrosion may require higher concentrations.

To assess the requirement of Earth Pro Brine-Cor in any condition, it is best to use a corrosion rate method such as corrosion ring analysis or an instantaneous corrosion monitor. If high corrosion rates persist and are determined to be oxygen related, supplemental additions of an oxygen scavenger such as Earth Pro Brine-Oxy should be added to the system.

Earth Pro Brine-Cor may be used in conjunction with Earth Pro Brine-Oxy brine oxygen scavenger and Earth Pro Brine-Lube brine lubricant.

Myacide GA25 is corrosive and will cause irreversible eye damage.  Wear suitable protection for eyes and skin and ensure there is adequate ventilation in the mixing area.

  • High yielding
  • Highly dispersible and fast mixing
  • Environmentally friendly
  • Reduce waste
  • Lubrication and fluid loss control
  • Compatible in cement grouts

Linear

Traditional

Traditional

Linear

Modern

Modern

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Modern

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Modern

Traditional

Linear

Linear

Linear

Modern

Modern

Traditional

Traditional

Traditional

Traditional

Traditional

Traditional

Linear

Mixing & Handling

Physical Properties

Physical Properties

Mixing & Handling

Mixing & Handling

Application

Mixing & Handling

Mixing & Handling

Physical Properties

Physical Properties

Physical Properties

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Application

Mixing & Handling

Physical Properties

Mixing & Handling

Cementing Application

Mixing & Handling

Mixing & Handling

Mixing & Handling

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Mixing & Handling

Mixing & Handling

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Chemical Properties

Physical Properties

Physical Properties

Physical Properties

Mixing & Handling

Physical Properties

Mixing & Handling

Physical Properties

Quality Control Test Criteria

Setting Time

Mixing & Handling

Physical Properties

Physical Properties

Mixing & Handling

Physical Properties

Chemical Properties

Physical Properties

Mixing & Handling

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Mixing & Handling

Specifications

Physical Properties

Packaging & Controls

Mixing & Handling

Mixing & Handling

Concentration

Concentration

Concentration

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Mixing & Handling

Concentration

Physical Properties

Physical Properties

Application

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Premier Silica (NSF Certified)

Casing Protector Sizes Available

Anchors Available

Schedule 40 F-480

Specifications

Specifications

Well Development

Damaged Wells

4" HydraSleeve - 2.5 Liter

Kwik Klamp 2

Mixing & Handling

Specifications

Specifications

Specifications

Optional Item

Specifications

Specifications

Specifications

Optional Items

Specifications

Specifications

Requirements

Specifications

Specifications

Control & Processing

Mixing & Handling

Mixing & Handling

Physical Properties

Characteristics

Characteristics

Application

Physical Properties

Mixing & Handling

Accessories

Optional Equipment

Mixing & Handling

Physical Properties

N Sizes Available

N Sizes Available

N Sizes Available

N Sizes Available

N Sizes Available

BTW Sizes Available

H Sizes Available

BU Compact Plus Water Swivel Spares Kit and Parts

BU Core Barrel Assembly & Options

BU Head Assembly & Options

N Core Barrel Spares

BU Overshot Assembly

N Overshot Spares

Mixing & Handling

Physical Properties

Mixing & Handling

Physical Properties

Mixing & Handling

Appearance: White granules or powder

Molecular Weight: 330.34

Bulk Density: 0.96 - 1.2 g/cc

Ultra Seal can be mixed through the mud hopper or directly into the mud system at a point of agitation.

Note: A dust hazard is present while Ultra Seal is being mixed. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Appearance: Cream-tan powder

Moisture Content: 13.3%

Bulk Density: 640 - 961 kg/m³

Earth Pro Oilwell ‘G’ Cement is not hazardous. However, if product becomes wet through unforeseen circumstances, some heat will be given off due to hydration. Avoid excessively humid conditions. Store in a cool dry place.

Earth Pro Oilwell ‘G’ Cement contains free silica. Avoid breathing dust, and wear appropriate dust mask as a precaution. When product is mixed with water, some heat evolution will occur. Caution should be exercised to mix continually until ready to place the slurry in the dump-bail.

Since Earth Pro Oilwell ‘G’ Cement is caustic in nature (pH 10-12), and will cause severe burns to the eyes and other sensitive skin areas. Wear the appropriate safety goggles and protective equipment when handling this product.

Appearance: Clear liquid

Density: 0.85 - 0.88 g/cc @ 20°C

Test Items Units Limits
Particle size >20 mesh (841 microns), max Wt% 0
API/ISO Static Fluid Loss @ 40°C, max (see note for slurry formation) ml <30
Specific Gravity - 1.60 +/- 0.05 g/cm³
pH (1% solution in water) - 6.0 - 8.0

Note - For laboratory testing the following weights for standard density slurry are to be used: Earth Pro Oilwell 'G' Cement: 792.0 g, tap water: 349.0 g, Earth Pro FLA-6: 5.54 g, LTR (Low Temperature Retarder): 3.17 g, liquid defoamer: 0.7 mL. The fluid loss test is performed at 40°C and 1000 PSI.

Slurry Volume per Pail (20kg) ResinBond 13.6 liters
Slurry Density 1840 kg/m³
pH 6.0 - 8.0 (1% w/v demineralized water)
Compressive Strength > 10 MPa in 24 hours

Earth Pro ResinBond Cement is a unique blend of polymer and high purity gypsum that has been purposely designed to provide 90-120 minutes of open time, or fluid state to enable proper mixing and displacement to the desired plug zone.

Combined with RB Catalyst, low viscosity fluid properties are maintained for 30 - 60 minutes at BHT provided proper mixing procedures are followed, and product does not become contaminated. This enables confident placement at a wide variety of depths and wellbore temperatures.

Due to this delay feature, should another plug of the same type be required on top of the first one, a certain amount of waiting time is necessary to ensure adequate strength on the preceding plug to prevent disturbance of the weak bonds.

Generally, a minimum of 4 hours is required to allow proper set and initial cure before another similar plug may be placed on top. It is recommended that a retain (cup sample) of the slurry be taken after mixing and monitored at surface (above freezing temperature), to provide a more accurate indicator of the slurry set.

Aluminum Powder 200 is of low toxicity. Excess dust may however produce irritation of the eyes and respiratory system. Use good industrial
hygiene practice and wear goggles and a dust mask when handling the material.

Store in a cool, dry, well-ventilated area away from sources of heat, ignition, sparks and incompatible materials such as oxidizers, halogenated hydrocarbons, some acids and alkalis. Keep material dry as aluminum powder will react with water and slowly generate heat and hydrogen.

Appearance: White crystals

Density: 1.44 g/cc

Appearance: Pale brown liquid

Bulk Density: 0.80 - 0.81 kg/L @ 15°C

Volatile Content: 95-96%

Daxad 19 can be dry blended or dispersed in water. Care should be taken to avoid breathing dust.

Appearance: Reddish brown powder

Bulk Density: 500-700 kg/m³

Viscosity: 2100-2400 cP (Brookfield LVT 30 RPM, spindle 63)

Microtox: 142.6 L/m³

Appearance: Brown powder

Bulk Density: 320-500 kg/m³

Moisture Content: <7%

Metso Beads 2048 can be added directly through the admix bottle or pre-dissolved in the cement mix water tank prior to use. If pre-hydrating in water, calcium chloride must added first to ensure gel formation. Metso Beads 2048 exhibit a natural tendency to absorb humidity from the air. When stored in humid air for prolonged periods, these products may become sticky and cake into solid masses. Store product in a dry place and ensure packaging is tightly sealed.

Appearance: Light grey

Specific Gravity: 0.6-0.8

Bulk Density: 320-400 kg/m³

Particle Size: 10-300 microns

Average Wall Thickness: 10% diameter

Crush Strength: 3500-5000 psi

Softening Point: >2700°F

Appearance: Slightly grey granules

Appearance: White pellet

Bulk Density: 1122 kg/m³

Specific Gravity: 1.94 gm/cm³

Particle Size Distribution:

Mesh Size #30 #40 #50 #70 #100 #150 Pan
Microns 600 425 300 212 150 106 <100
% Retained 1 14 25 30 15 9 6

Appearance: Light grey powder

Specific Gravity: 2.1 - 2.4

Bulk Density: 608 - 720 g/cm³

Particle Size: 0.4 microns

Appearance: White granular crystals

Specific Gravity: 2.533 gm/cm³

Bulk Density: 930 kg/m³ (min)

Appearance: White crystals

Specific Gravity: 2.7 gm/cm³

Bulk Density: 1285-1445 kg/m³

Melting Point: 884°C

Particle Size Distribution: 

Mesh Size #20 #35 #60 #100 #200 #400 Pan
Microns 850 500 250 150 75 38 0
% Retained 0 12.2 30.9 28.7 18.7 5.5 4.0

Appearance: Colorless liquid

Specific Gravity: 1.16

Flash Point: >93°C (closed cup)

Pour Point: -30°C

Appearance: Colorless liquid

Specific Gravity: 1.23

Flash Point: >93°C

Pour Point: -30°C

Appearance: Brown to grey powder

Specific Gravity: 4.2 - 4.4

Melting Point: 1580°C

May be used for all types of freshwater drilling but yield may vary depending on quality of water. High salinity or low pH will adversely affect yield. Ideal pH range for hydration is 8-10 and total hardness should be less than 80 mg/L (Calcium + Magnesium)

  • 40 kg/m³ regular drilling applications
  • 60-80 kg/m³ lost circulation applications for suspension of LCM solids
  • 15-20 kg/m³ as filter cake enhancer in polymer systems

Earth Pro X-TRA Gel should not be mixed directly into salt water. Pre-hydrate in fresh water before adding to salt or brackish fluid. Expect yield to be diminished.

Typical E.P. Toxicity Analysis
  Standard ppm Set Grout ppm
Arsenic 5.0 <0.10
Barium 100.0 0.50
Cadmium 1.0 <0.05
Chromium 5.0 <0.10
Lead 5.0 <0.10
Mercury 0.2 <0.02
Selenium 1.0 <0.05
Silver 5.0 <0.10

 

  17.7% Solids 20.0% Solids
Grout-Well DF 50lbs 50lbs
Water 28 gal 24 gal
Usable Slurry 31 gal 27 gal

Appearance: Semi-solid tan paste

Specific Gravity: 1.1  

Melting Point: >205°C 

Boiling Point: >260°C

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail / 3.8L pail

Avoid contact with strong oxidizers. Safety glasses with side-shields are recommended. Wear clothing adequate to protect against exposure. Ensure eye-wash station and emergency shower are available. Wash thoroughly after handling. Avoid contact with eyes, skin or clothing.

Tru-Bore is dry bentonite clay and requires high shear and agitation for proper hydration. It should be mixed no faster than five minutes per sack. Always mix bentonite before polymers. Cold water increases mixing time.

Tru-Bore concentrations vary dependent on the application and type of additives used. A concentration of 15-25 pounds of Tru-Bore per 100 gal of fluid yields a viscosity of approximately 45 seconds on a Marsh Funnel. At a rate of 27 lb per 100 gal, viscosity can climb to 60 seconds.

.25-1 L/m³ is more than sufficient. Too much will result in an increase in apparent viscosity as it will begin to flocculate the mud.

When mixed in a polymer system in conjunction with Earth Pro HydraVis D, Earth Pro HydraVis L, Earth Pro SynVis D or Earth Pro SynVis L mix at 2-4kg/m³. As a rheology and fluid loss additive in bentonite based systems add 1-4kg/m³ as required to maintain fluid loss below 10CC.

If Earth Pro HydraVis L is used in conjunction with Earth Pro SynVis L the concentration should be 2L/m³. If used as a stand alone product the concentration should be 3-4L/m³. If used as a bentonite extender the concentration should be 1.5L/m³.

Fill available tanks with fresh water and apply maximum agitation to allow for quicker dispersion and hydration of initial application. Slowly add 1kg Earth Pro MultiMix to 1000L of water and allow to hydrate at maximum shear in the tank for 5 mins.

While pumping mixture down, add an additional 2 kg/m³ as close to the suction point as possible to allow for semi hydrated polymers to reach formation. As the semi hydrated polymers are hydrated in or on the surface of the formation, they will form a securing polymer matrix that will halt further sloughing and collapse.

Regular drilling applications in potential sloughing sand and loose overburden should be met with 2 kg/1000 L of water of Earth Pro MultiMix mixed and hydrated in the surface tanks like normal drilling polymers. Regular semi hydrated sweeps of Earth Pro MultiMix may also benefit broken ground conditions. Sweep by adding .5 kg of drill Earth Pro MultiMix at a point close to the suction in the mud tanks while pumping.

Mix the Earth Pro StopLoss directly in the tank with 200 times its volume water. Wait 10 minutes. Inject the mixture into the drill string. Inject a volume of water to move mixture to the correct location. Wait 20 minutes. Drill. If the problem persists attempt treatment a second time.

or

Place 1 gallon of dry Earth Pro StopLoss in a 2 0-liter pail with 10 liters of water. Allow Earth Pro StopLoss to partially swell. Add 1 liter of partially swollen Earth Pro StopLoss to the rods after the core tube has been pulled. Pump down hole and replace inner tube. Repeat as necessary to stop loss.

Earth Pro SynVis L can be added either by either batch measuring the prescribed amount and adding at a point of agitation or continuous additions by poking a small hole in the bottom and top of the pail and placing near a point of agitation above the tank.

If being mixed as part of a complete polymer system add approximately 2 L for every m³ of fluid under normal drilling situations. If being mixed as a standalone product increase the mixture to 3.5-4 L/m³ and vary concentration depending on hole conditions. If being added as an overburden binder or to a bentonite system as an extender add 3 L/m³ after the bentonite has been added to the mix and allowed to hydrate.

DR-133 Polymer can be added either by either batch measuring the prescribed amount and adding at a point of agitation or continuous additions by poking a small hole in the bottom and top of the jug and placing near a point of agitation above the tank.

If being mixed as part of a complete polymer system add approximately 2L for every m³ of fluid under normal drilling situations. If being mixed as a standalone product increase the mixture to 3.5-4 L/m³ and vary concentration depending on hole conditions. If being added as an over burden binder or to a bentonite system as an extender add 3 L/m³ after the bentonite has been added to the mix and allowed to hydrate.

For optimum performance, Boreliner should be added to a system before the troublesome zone is penetrated or as soon after as possible. Premix the prescribed amount or Boreliner in the surface system by adding it at a point of agitation near a mixer in the tank.

For enhancing filter cake in troublesome shale and sands use a concentration of 9.0 to 17.0 kg/m³. For shock treatment of a zone that has already been penetrated mix 20-30 kg/m³ in the initial 2-3 m³ of fluid then maintain the concentration at 5-10 kg/m³ until the zone has been completely drilled and 1 hour afterwards.

Boreliner is a hydrocarbon based product which is not considered biodegradable. The dust from the product warrants the use of a dust mask when mixing and handling to prevent inhalation. At low concentrations the product is non toxic to the environment.

Concentration for initial treatments should be 3-4L/m³ and then maintenance should be at 2-3L/m³ (this should be monitored closely). Situations may require concentrations up to 10L/m³ or as low as 2L/m³.

Appearance: Yellow and white granules

Specific Gravity: 2.6

Dropping Point (ASTM D-2265): >230°C (450°F)

Specific Gravity: 1.30

Density: 1.30

Flash Point (ASTM D-217): 300 -330

Modified Starch is more efficient than regular starches and nearly as efficient as PAC at controlling fluid loss. It has a synergistic effect with bentonite and other polymers which enhances the shear thinning properties of drilling fluids and results in excellent hole cleaning at low shear rates. Modified Starch can also coat clay and shale particles to control clay dispersion, slow well bore destabilization, and facilitate the removal of drilled solids on surface.

Modified Starch can be combined with PAC as a low cost extender. Blends typically contain 1:1 – 3:1 Modified Starch/PAC. Modified Starch is effective in all types of water-based fluids and at temperature up to 150°C with the use of an oxygen scavenger. It is non-fermenting and requires no biocide under normal conditions. Filter cakes containing Modified Starch can be easily removed using Can-Break ECA.

Modified Starch is used in concentrations ranging from 4.0-12.0 kg/m³, depending on fluid loss requirements and the amount of solids in the system.

Appearance: Milk-white liquid

Specific Gravity: 1.04 - 1.06

Pour Point: -10°C

Flash Point: >93°C

Appearance: Grayish white crystalline powder

Boiling Point: 320°F (160°C)

Specific Gravity: 2.1 @ 68°F (20°C)

Melting Point: 268°F (131°C)

Appearance: Clear amber liquid

Boiling Point: 243°F

Specific Gravity: 1.27

Appearance: Clear, light amber liquid

Boiling Point: 235°F

Specific Gravity: 1.12

Appearance: Silver

Dropping Point: 260°C

Specific Gravity: 1.10

Density: 1.10

Dropping Point: 260°C

Appearance: White granular crystal

Bulk Density: 930 kg/m³ (min)

Specific Gravity: 2.533 gm/cm³

Particle Size Distribution:

Mesh Size #20 #30 #40 #100 #140 #200 Pan
Microns 850 600 425 150 106 75 <75
% Retained 0.5 max 3.0 max 30.0 max 85.0 min 93.0 min 98.0 min 2.0 max

Appearance: Colorless liquid

Specific Gravity: 1.1

Crystallization Point: -18°C

Appearance: Opaque liquid

Specific Gravity: 1.05

Pour Point: -30°C

Flash Point: >100°C (TCC)

Appearance: Opaque liquid

Specific Gravity: 1.05

Pour Point: -30°C

Flash Point: >100°C (TCC)

Product Number Product Name Packaging
47366 Silica Sand 6/9 50lb
31203 Silica Sand 8/12 50lb
47389 Silica Sand 10/16 50lb
31204 Silica Sand 10/20 50lb
49012 Silica Sand 12/20 50lb
44439 Silica Sand 16/30 50lb
27071 Silica Sand 20/40 50lb
48814 Silica Sand 30/70 50lb

Product Number Size Wall Thickness Description
41160 4-1/2" x 5' .188" Casing Protector
41169 5-9/16" x 5' .188" Casing Protector
49680 6-5/8" x 2.5' .188" Casing Protector
41165 6-5/8" x 5' .188" Casing Protector
49457 8-5/8" x 5' .188" Casing Protector

Product Number Product Description
48909 QC Slope Indicator Anchor for 85 mm (3.34”) Casing
49019 QC Slope Indicator Anchor for 70 mm (2.75”) Casing

Product Number Size TPI Description
41080 2” x 5’ 2 .010” Slotted
41088 2” x 5’ 2  
41094 2” x 5’ 2 .010” Slotted
41095 2” x 5’ 2 .020” Slotted
41186 2” x 5’ 4  
41188 2” x 5’ 4 .010” Slotted
41190 2” x 5’ 4 .020” Slotted
47230 2” x 5’ 2 .020” Slotted
41096 2” x 10’ 2 .010” Slotted
41097 2” x 10’ 2 .020” Slotted
41185 2” x 10’ 4  
41187 2” x 10’ 4 .010” Slotted
41189 2” x 10’ 4 .020” Slotted
49488 2” x 10’ 2 .030” Slotted

Dimensions 15" length, 20" height, 7" width (38 cm L x 51 cm H x 18 cm W)
Weight 38 lbs (17.25 kg)
Powered by 3/4 hp (6 amps) volt DC electric motor
Performance Characteristics Generates a 4" stroke, adjustable 0-180 cycles/min
Additional Requirements 110 VAC or 220 VAC power supply
For Use With Inertial Pumping Systems — Standard FlowHigh FlowLow Flow

Dimensions 15.5" length, 22.5" height, 14.5" width 
(39cm L x 57cm H x 37cm W)
Weight 28.6 lbs (13kg)
Power by Honda GX25 (25cc Mini 4-Stroke OHC gasoline engine)
Performance Characteristics Generates a 4" stroke, 
adjustable 0—140 cycles/min
Additional Requirements Regular gasoline, SAE 10W-30 motor oil
For Use With Inertial Pumping Systems —Standard Flow, High Flow, Low Flow

The Inertial Pump has a substantial capacity for developing monitoring wells because of the cyclical action of the valve in the well screen area. This characteristic can be utilized to remove silt and sediment that has accumulated in the foot of the monitoring well and can also be used to remove fines from the sand pack and well screen.

The well development capacity of the High Flow D-32 foot valve can be enhanced by installing a SBD-32 Surge Block to the D-32 foot valve. The Surge Block is an excellent well development tool. It simply press fits over the body of the Standard Flow Foot Valve or High Flow Foot Valve (D-25 or D-32).

The Surge Block effectively increases the outside diameter of the D-25 or D-32 foot valve to 1-7/8” In 2” wells and 3-7/8” OD in 4” wells, reducing the annular gap between the valve and the inside of the well screen to approximately 1/16”. This results in a significant increase in the surging action of the valve.

The use of the Inertial Pump and Surge Block together is one of the most effective methods for developing monitoring wells because it simultaneously surges and pumps the well. This frees up silt and sediment in the sand pack and screen and breaks down bridging, drawing these particles it into the well and then removes this material from the well.

The recommended method for developing a monitoring well with the Inertial Pump and Surge Block is to begin the development process with the Surge Block near the top of the well screen. Operate the pump with the Surge Block in this position until the turbidity level of the water being delivered from the pump decreases to an acceptable level. Once this level is reached then the Surge Block is lowered in the well screen one to two feet and the process is repeated. Developing wells in this manner is one of the best methods, often resulting in turbidity levels below 10 NTUs.

The development capacity of the High Flow System is greater than that of the Standard Flow System because the pump generates a higher flow rate and the larger diameter tubing is stiffer and flexes less in 2” monitoring wells.

The Micro Flow System is also useful for sampling in damaged or obstructed monitoring wells. The maximum outside diameter of the Micro Flow System is 3/8” (10mm). This small maximum diameter allows this pump to fit into many tight situations that outer devices can't get near.

  • 4-inch HydraSleeve made to hold greater than 2.5 liters of sample volume
  • 2.9 inches O.D. by 37 inches long.  Fill within a 7-foot column.  Lay-flat width 4.614 inches
  • Absolute maximum volume obtainable without spilling 3.1 liters
  • Layflat = 4.61"W x 37"L
  • Filled Diameter = 2.9"
  • Filled Volume = ~2500 mL
  • Fill Stroke = 37"

The heavy duty Kwik Klamp 2 is the driller's answer for holding the larger pipe sizes 2-1/2", 3", and 4". Kwik Klamp 2 is an enlarged version of our popular Kwik Klamp 1 which is for pipe sizes 1" through 2", with many of the same features. This tool has been used worldwide by environmental drillers, pump installers, well serviceman, and water well drillers.

  • Main body is constructed of 2" and 2-1/2" 1/4" wall steel tube.
  • Easy to operate, over center locking of jaws when downward pressure is applied to a 19" long lever handle.
  • 1/2" Safety pin used to prevent accidental unclamping.
  • Kwik Klamp 2 allows workers to bring pipe or drill joint up to an easy working level.
  • The tool weighs only 30 lbs. and is 20" long x 7-1/2" wide.
  • Jaws are equipped with 16 carbide tipped grippers.
  • Excellent holding capability, with load tests done over 7,000 lbs.
  • Designed to hold pipes 2-1/2", 3" and 4" (2.875"OD-4.5"OD) PVC, HDPE, stainless and galvanized steel.
  • Kwik Klamp is one of the safest, time saving tools you will ever own.
Product Number Description
41178 Kwik Klamp 2 for 2.5” to 4.5” Pipe
47334 Kwik Klamp 2 Spacers for 4.5” Pipe

Avoid eye and skin contact, should contact occur, flush thoroughly with water and seek proper medical attention. Wear plastic or latex gloves and chemical splash goggles. Do not wear contact lenses when handling this material. Wear chemical impervious clothing. Wash thoroughly after handling. Keep containers tightly closed at all times.

Size and Thread Depth Capacity* Pullback** (rated minimum)
BWL 1.5 m (5 ft) / 3 m (10 ft) 1500 m (5000 ft) TBA kN (TBA lbf)
NWL 1.5 m (5 ft) / 3 m (10 ft) 2000 m (6500 ft) 222 kN (50,000 lbf)
HWL 1.5 m (5 ft) / 3 m (10 ft) 1500 m (5000 ft) 333 kN (75,000 lbf)

*Depth capacity ratings are based on published industry values. Di-Corp uses comparable materials and manufacturing processes, and is confident the same results will be achieved. It is important to note that the care and handling, in addition to drilling conditions, practices, and equipment will play a significant role in the ultimate depth capacity and performance of any drill rod.

**Di-Corp is testing its rod offering at an independent facility and will publish values as they become available. Pullback is rated on a new, unused drill rod.

  • Instrument Geometry: True Couette Coaxial Cylinder
  • Speed Accuracy (RPM): 0.1
  • Motor Speeds (RPM): 8 Fixed Speeds (600, 300, 200, 100, 60, 30, 6, and 3)
  • Readout: Direct Dial
  • Shipping Dimensions: 22 x 14 x 10 inches (56 x 36 x 25 cm)
  • Shipping Weight: 25 lb (11 kg)
  • Power Requirement: 115 / 230 VAC, 50/60 Hz
  • Power Requirements: 13 - 16 VDC

  • Size: 3.5” x 4” x 11.0” (9 x 10 x 28 cm)
  • Weight: 7 lb 9 oz (3.4 kg)
  • Maximum Temperature: 1000°F (537° C)
  • Temperature Control: Standard – Electronic Fixed Temperature Control
  • Cell Capacity: 10 mL
  • Heating Capacity: 350 Watts
  • Power Requirement: 115 Volt at 3 Amp or 230 Volt at 1.5 Amp, 50/60 Hz

  • 20 mL Receiver Tube for Retort, 2-scales, 0-100% × 0.1, 0-20 mL × 0.1 mL, with certificate

50 mL Retort Kit with Thermostat (115V) and 50 mL Retort Kit with Thermostat (230V)

  • Temperature Control: Standard – Electronic Fixed Temperature Control

50 mL Retort Kit, with Electronic Temperature Controller (115V) and 50 mL Retort Kit, with Electronic Temperature Controller (230V)

  • Temperature Control: Electronic Variable Temperature Control
  • Maximum Temperature: 1000°F (537° C)
  • Cell Capacity: 50 mL
  • Heating Capacity: 500 Watts
  • Power Requirement: 115 Volt at 3 Amp or 230 Volt at 1.5 Amp, 50/60 Hz
  • Size: 9 × 7 × 12 inches (23 × 18 × 30 cm) 20 lb (9.07 kg)
  • Weight: 20 lb (9.07 kg)

  • Maximum Pressure: 250 PSI (1,735 kPa)
  • Pressure Source: Any non-hazardous gas
  • Filtration Area: 7.1 ± 0.1 in (4,580 ± 60 mm)
  • Filter Paper Size: 3.5” (9 cm)

  • Temperature Range: 100 - 450°F (38 - 232.2°C)
  • Digital Temperature Controller
  • Motor Speed: 25 RPM
  • Programmable Timer
  • Heater: 2 x 350 Watts
  • Material:
    • Cabinet: 303 Stainless Steel
    • Rollers: 304 Stainless Steel
  • Capacity (Aging Cells sold separately):
    • 260 mL Aging Cells: 6
    • 500 mL Aging Cells: 3
    • 1000 mL Aging Cells: 3
  • Power Requirements:
    • 115 Volt/230 Volt
  • Dimensions:
    • Size: 26.75” × 22” × 26” (70 × 56 × 66 cm)
    • Weight: 141 lb (64 kg)
    • Crated Size: 35” × 29” × 36” (89 × 74 × 91 cm)
    • Crated Weight: 239 lb (108.4 kg) 1 lb (64 kg)

  • Thermometer, 5” Stem, Metal Dial, 0° - 220°F (-10° - 100°C)
  • Thermometer, Pocket, 5” Stem, 1” Dial, 0° - 220°F
  • SP - Spare Parts Kit for Emulsion Stability Tester
  • Probe for ES Meter
  • Battery, 9 Volt, Alkaline

  • Size: 3” × 4” × 4.5” (8 × 10 × 11 cm)
  • Weight: 2.6 lb (1.2 kg)

The High Pressure SGSM fits in a high-pressure UCA test cell. This configuration is compatible with both the Single Cell UCA and the Dual Cell UCA, as shown in the picture.

  • Maximum Temperature: 400°F (204°C)
  • Maximum Pressure: 20,000 PSI (138 MPa)
  • Size (Including Cell): 20” Tall × 6” Diameter (51 × 15 cm)
  • Weight: 50.6 lb (23 kg)

  • Air/Nitrogen Supply (100 - 150 PSI / 690 - 1,035 kPa)
  • Water Supply for Cooling (40 PSI / 276 kPa)
  • Water Drain

  • Maximum Pressure: 40,000 PSI (275.8 MPa)
  • Maximum Temperature: 600°F (315°C)
  • Consistency Range: (0 - 125 Bc)
  • Digital Temperature Controller with 0.1° resolution
  • Pressure indicator resolution is 100 PSI and includes both high- and low-pressure alarms
  • Slurry cup rotational speed is 150 RPM
  • Size: 22.5" × 27.5" × 70" (57 cm × 70 cm × 178 cm)
  • Weight: Approx. 450 lb (204 kg)
  • Crated Size: Approx. 26" × 34" × 76" (66 cm x 86 cm x 193 cm)
  • Crated Weight: Approx. 750 lb (340 kg)

  • Maximum Temperature: 400°F (260°C)
  • Maximum Pressure: 2,000 PSI (13,880 kPa)
  • Pressure Source: Nitrogen (at least 1500 PSI / 10,343 kPa)- Sold Separately
  • Test Cell Capacity: 500 mL
  • Heater: 800 Watt
  • Size: 10” × 18” × 42” (25.4 × 45.7 × 106.7 cm)
  • Weight: 53 lb. (24.1 kg)
  • Shipping Size: 29” × 12” × 16” (74 × 30.5 × 41 cm)
  • Shipping Weight: 65 lb. (29.5 kg)
  • Power Requirement: 115 Volt/230 Volt

The isCompass is delivered with a rugged handheld computer, the Nautiz X5, running Windows Mobile 6.1. All operations and downloaded data are processed by the computer and can be viewed directly on the handheld device. Quality measurements of survey stations are also provided.


Field control unit: Nautiz X5, fully rugged handheld (MIL-STD-810G)

Operating time: Full day of normal operation on one battery (spare battery included)

Survey Software: isCompass

Operating System: Windows Mobile 6.1

Date transfer: USB

SMS can be added directly through the admix bottle or predissolved in the cement mix water tank prior to use. If prehydrating in water, calcium chloride must added first to ensure gel formation. SMS exhibits a natural tendency to absorb humidity from the air. When stored in humid air for prolonged periods, these products may become sticky and cake into solid masses. Store product in a dry place and ensure packaging is tightly sealed.

The extending properties of bentonite can be greatly enhanced if the material is allowed to completely hydrate in the mix water prior to slurry mixing. The presence of high concentrations of calcium ion in the aqueous phase of cement slurry inhibits the hydration of Puregold Gel.

Appearance: White or grey-white flakes

Bulk Density: 2150 kg/m³

  • 98% minimum passing 4 mesh
  • 5% maximum passing 20 mesh
  • NSF Certified

  • 97% minimum passing 8 mesh
  • 5% maximum passing 20 mesh
  • NSF Certified

Hole Diameter 2" Casing 4" Casing 6" Casing
4 0.4 gal/ft N/A N/A
8 1.3 gal/ft 0.7 gal/ft N/A
6 2.3 gal/ft 1.8 gal/ft 0.8 gal/ft
10 3.8 gal/ft 3.2 gal/ft 2.3 gal/ft

Appearance: Tan colored powder

Specific Gravity: 1.2

Used as a Slurry Fluid: Maintaining formation integrity while cutting lays the foundation that keeps jacking pressures low. Using Micro-Gel as the slurry fluid limits negative impact on soils and maintains the bore wall continuity. Mixing rate should be 320 pounds of Micro-Gel per 1000 gallons (144 kg/3.8 m³ ). Fluid characteristics will have a Marsh Funnel Viscosity of 45 to 48 sec/qt.

Used as a Lubricating Fluid: For best results, a venturi or other high-shear equipment should be used. Mix rate is 22.5 pounds per barrel or 535 pounds per 1000 gallons (241 kg/3.8 m³ ) of make-up water. This mix ratio will yield a Marsh Funnel Viscosity of 80 to 85 sec/qt.

Part Number Description
30685 N3 Kleer-Kore End Cap
30684 H3 Kleer-Kore End Cap
39596 P3 Kleer-Kore End Cap
39570 Kleer-Kore Tube Box 5'
39571 Kleer-Kore Tube Box Insert

Description

Part Number
Overshot Swivel Assembly 25555112
Wireline Extension Rod 18in (.46m) 27012485
Wireline Extension Rod 46in (1.17m) 25555079
Positive Latch Lowering Tool 25361023
Loading Funnel 3760008036

Super-Sweep Fiber is easily added and pre-mixed in the drilling fluid at various concentration levels, depending on the level of solids suspension desired. In water, a minimum dosage of one box (15 pounds) of Super-Sweep Fiber per 30 barrel sweep has shown to be an effective addition level to remove cuttings and solids.

In drilling mud, a minimum dosage of one box (15 pounds) of Super-Sweep Fiber per 60 barrel sweep has proven effective. The fluid with the Super-Sweep Fiber is then introduced by pump suction to the drilling fluids system and circulated through the drilling system. The Super-Sweep Fiber and transported cuttings are removed by the shaker or discharged to the reserve pit. 

Appearance: Black-grey powder

Specific Gravity: 2.25

Moisture Content: 0.5%

Part Number Description
102606 NWL Rod Box to Tubing Blank
102607 ND Rod Box to Tubing Blank
102608 NWL Rod Pin to Tubing Blank
102609 ND Rod Pin to Tubing Blank

Part Number Description
100685 NWL Rod Box to NW Rod Pin (Rod to Casing)
102593 ND Rod Box to NW Rod Pin (Rod to Casing)
100684 NWL Rod Box to BW Rod Pin (Rod to Rod)
101133 ND Rod Box to BW Rod Pin (Rod to Rod)

Part Number Description
100834 NWL Rod Box to ND Rod Pin
100835 ND Rod Box to NWL Rod Pin

Part Number Description
100667 AW Rod Pin to NWL Rod Pin (Compact)
100852 AW Rod Pin to ND Rod Pin (Compact)
100593 BW Rod Pin to NWL Rod Pin (Universal)
102588 BW Rod Pin to ND Rod Pin (Universal)

Part Number Description
103349 NW Casing Bit
102796 HWL Casing Bit

Part Number Drilling Parameter Edge Series Waterway Configuration
103353 BTW 2-4 Edge 2 Abrasive Standard
101602 BTW 4-6 Edge 5 Standard
101211 BTW 4-6 Edge 5 Wide
101603 BTW 6-7 Edge 6 Standard
101639 BTW 6-7 Edge 6 Wide
103354 BTW 7-8 Edge 7 Standard
101638 BTW 6-8 Edge 7 Endurance Standard
101640 BTW 6-8 Edge 7 Endurance Wide
101777 BTW 7-8 Edge 8 Standard
103610 BTW 7-9 Edge 8 Endurance Standard
101209 BTW 7-10 Edge 9 Standard
101210 BTW 7-9 Edge 9 Endurance Standard
101641 BTW 7-9 Edge 9 Endurance Wide
103167 BTW 9-10 Edge 10 Standard

Part Number Description
102217 HWL (T11) Rod Shoe 
102662 HWL (T12) Rod Shoe
103824 HWL Carbonado OS 4.765 Rod Shoe

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
100756 Core Barrel Assembly, 3 m (10 ft) -
100755 Core Barrel Assembly, 1.5 m (5 ft) -
100739 Locking Coupling, Conventional, No Tang
102490 Adaptor Coupling
100737 Landing Ring 1
100726 Outer Tube, 3 m (10 ft) 1
100758 Outer Tube, 1.5 m (5 ft) -
100734 Inner Tube Stabilizer 1
100752 Head Assembly 1
100725 Inner Tube, 3 m (10 ft) 1
100757 Inner Tube, 1.5 m (5 ft) -
100730 Stop Ring 1
100731 Core Lifter, Slotted 1
100733 Core Lifter Case 1

 

Options
Part Number Description
100763 Locking Coupling, Full Hole, No Tang
100551 Landing Indicator Bushing, No OD Groove
100582 Shut-Off Valve, Soft
101818 Solid Spindle Spacer
101821 Inner Tube Cap Assembly, With Thd. Protector
100708 Inner Tube Coupling
100762 Inner Tube Extension, Stabilized (10") Shell
101810 Inner Tube Extension, Double Stabilized (18") Shell
100732 Core Lifter, Fluted
101623 Core Lifter, Slotted, Diamond Coated
101624 Core Lifter, Fluted, Diamond Coated
101566 Core Lifter, Smooth
100644 Graphite Core Barrel Plug
101104 Gauge Assembly, Bit & Shell
100776 Outer Tube, Chrome Plated, 3.0 m (10 ft)
100775 Outer Tube, Chrome Plated, 1.5 m (5 ft)
100761 Inner Tube, Chrome Plated, 3.0 m (10 ft)
100760 Inner Tube, Chrome Plated, 1.5 m (5 ft)
101152 Parts Pouch
100611 Fluid Retention Kit
102452 Quick Coupler, #16 NPT Female

Part Number Description Qty
100752 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100712 Spearhead Base 1
100747 Latch Locking Spring 1
100746 Latch Locking Pin 1
100701 Latch Retracting Pin 2
100743 Latch Retracting Case 1
100744 Latch Retracting Case Pin 1
100745 Latch Body, Upper 1
100702 Latch Pivot Pin 1
100722 Latch Spring 1
100715 Latch 2
100827 Spring Seat 1
100801 Latch Retracting Case Spring 1
100826 Spring Sleeve 1
100828 Spring Cavity Bushing 1
100749 Latch Body Adaptor 1
100750 Pump-In Seal 2
100751 Latch Body Seal Seat 1
100452 Stainless Steel Ball 1
100468 Landing Indicator Bushing, OD Groove 1
100716 Landing Shoulder 1
100717 Latch Body, Lower 1
100703 Nord-Lock Washer 1
100704 Hex Nut 1
100718 Spindle 1
100705 Shut-Off Valve, Hard 2
100706 Shut-Off Washer 2
100707 Spindle Bearing 2
100719 Spindle Bushing 1
100709 Compression Spring 1
100711 Self Locking Hex Nut 1
100721 Inner Tube Cap Assembly, No Thd. Protector 1
100639 Thread Protector, Inner Tube Cap 1

 

Part Number Description Qty
100504 Core Barrel Spares Kit -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Coiled Spring Pin, ø7/16" x 1" Long 2
100449 Latch Retracting Pin 2
100450 Latch Spring 2
100808 Latch 4
100451 Latch Pivot Pin 2
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 2
100469 Landing Shoulder 1
100454 Hex Nut 1
100455 Shut Off Valve, Hard 4
100457 Bearing, Upper 1
100458 Bearing, Lower 1
100460 Self Locking Nut 1
100461 Grease Fitting 2
100417 Stop Ring 2
100415 Core Lifter, Slotted 20
100416 Core Lifter Case 4
100439 Landing Ring 1
100443 Inner Tube Stabilizer 2

Part Number Description Qty
100890 Overshot Assembly -
100518 Cable Swivel Eye Bolt 1
100519 Cable Swivel Collar 1
100520 Thrust Bearing 1
100521 Castle Nut 1
100522 Cotter Pin 1
100461 Grease Fitting 1
100836 Cable Swivel Body 1
100838 Shear Pin 1
100884 Upper Body 1
100750 Pump-In Seal 2
100751 Latch Body Seal Seat 1
100452 Stainless Steel Ball 2
100468 Landing Indicator Bushing, OD Groove 1
100885 Overshot Head Body 1
100888 Compression Spring 1
100886 Pivot Pin 1
100887 Sway Pin 1
100889 Lifting Dog 2

Part Number Description Qty
101434 Overshot Spares Kit -
100520 Thrust Bearing 1
100521 Castle Nut 1
100522 Cotter Pin 2
100461 Grease Fitting 1
100526 Hex Nut, 3/4" UNC 1
100529 Compression Spring, Lifting Dog 1
100530 Lifting Dog 2
100531 Lifting Dog Pivot Pin 1
100532 Sway Pin 1
100535 Pin Link, Overshot 2
100539 Self Locking Cap Screw 4

When faced with the challenge of viscosifying saline water sources that exist in marine environments and in some cases terrestrial water sources Earth Pro SaltVis L rises to the occasion.

Concentration depends on the desired viscosity but most applications will see good hole cleaning and lubrication affect with a 2-4L/m³ concentration of Earth Pro SaltVis L.

Earth Pro SaltVis L can be mixed quickly to the desired concentration by pouring it in at a point of agitation in the mixing tanks or adding it through a hopper system.

Requires minimal shearing to yield very consistently and quickly compared to semi synthetic or natural polymers.

Appearance: Brown powder

Specific Gravity: 1.06

Flash Point: >93°C

Earth Pro Brine-Cor should be added directly to the mud system. It dissolves readily even in the heavier brines.

Avoid contact with eyes and skin. In case of contact, immediately wash with plenty of water. Flush eyes with flowing water immediately and continuously for twenty minutes. See a physician if necessary. Remove contaminated clothes and shoes and wash before re-use.

Appearance: Clear colorless to yellow liquid

Specific Gravity: 1.06 @ 20°C

Freeze Point: -5°C

Diamond Gel disperses in fresh water like no bentonite before it. The “norm” is to experience clumps of semi hydrated bentonite that can build up on core tooling or create a mess to clean up in a mud tank. Not Diamond Gel.  Mixing Diamond Gel is as easy as adding to a point of agitation in a mud tank or ideally through a mixing hopper as you would mix any bentonite.  Shearing with an in tank mixer is generally all that is required to yield a smooth high viscosity drilling fluid.

Diamond Gel can be used in cement + bentonite grouts without ill effect on cement making it a perfect one bag solution in environmental drilling as well. Always mix cement first then add bentonite.

Starting concentrations for most simple systems build of only Diamond Gel generally require less than 2 bags per 1000L. Consult with a Di-Corp representative to develop a fluids plan that works specifically for your application.

Appearance: White powder

Specific Gravity: 1.6

Earth Pro Chem Clean Green can be applied neat or diluted with water depending on the difficulty of a particular cleanup.

For extra heavy duty degreasing, Earth Pro Chem Clean Green can be used full strength. For routine cleaning, use Earth Pro Chem Clean Green can be diluted at 1:5 water. 

Skin and eye protection should be observed (see MSDS). Do not use Earth Pro Chem Clean Green on hot surfaces and hot or running motors. 

Earth Pro Corinox does not require any cumbersome equipment such as manual or automatic injection systems; therefore, it eliminates the problems of equipment failure and the cost of equipment rental and maintenance. 

Avoid contact with eyes, skin and clothing. In case of contact, immediately wash with plenty of water. Flush eyes with flowing water immediately and continuously for twenty minutes. See a physician if necessary. Remove contaminated clothes and shoes. Wash before re-use. 

Actual amount required depends upon the amount of solids present in the system, concentrations for normal use range from 0.4 - 4.0 L/m³ (requirements are typically 1/4 that of lignosulphonate).

Earth Pro Di-Sperse 72L should be added directly to the mud system. This product is stable at high and low temperatures and has excellent freeze-thaw stability.

The thinning efficiency of Earth Pro Di-Sperse 72L is actually improved by the presence of moderate levels of calcium up to a maximum of 800-1000 mg/L.

Earth Pro Drilling Detergent L can be irritating to the skin and eyes. Inhalation may cause nausea, vomiting and dizziness. In case of skin contacts wash with water.

In case of eye contact flush with water for fifteen minutes and seek medical attention. If ingested induce vomiting immediately and get patient to a physician.

*Danger* - This product contains ethylene glycol and lack of attention may cause kidney and liver damage.

Defoaming is a complex reaction, therefore, pilot testing may be necessary to determine optimum treatment rates and methods. Recommended treatment concentrations will vary depending on the severity of foaming, however, 0.5-1.5 L/m³ will be effective in most cases.

For maximum effectiveness, Earth Pro Foam Slayer should be added directly to the fluid system, as close to the point to foaming as possible.

Appearance: Light brown liquid

Specific Gravity: 1.06

Flash Point: >125°C

Appearance: White-tan powder

Appearance: Red powder

Although the use range can vary with well conditions the general addition rate would be 0.5-5 L/m³. It is indicated to maintain at all-time an adequate concentration of oil-wetting agent in the mud to prevent water-wetting of solids. Employ rubber gloves, rubber apron, and skin and eye protection and ensure mixing is done in an area with adequate ventilation.

Appearance: Clear liquid, sweet odor

Specific Gravity: 0.89

Flash Point: >80°C (PMCC)

Because of its excellent dispersibility and mixing Alcomer 60RD can be added directly to the mud system without pre-wetting in a solvent.

A small hole should be cut into the bottom of the bag, allowing it to flow at a steady rate into the mud hopper. If necessary Alcomer 60RD can be prehydrated at concentrations of 10.0-15.0 kg/m³ in a separate tank and fed into the main circulating system to maintain concentrations of 2.0-6.0 kg/m³.

Alcomer 60RD becomes very slippery when it comes in contact with water. A spill should be cleaned up with an absorbent material. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Mix Alcomer 755 / Zetag 7557 slowly into a chemical barrel or polymer mixing tank and allow product to hydrate. Avoid mixing too rapidly. Wear a mask and goggles to prevent dust inhalation and contact with eyes.

Alcomer 755 / Zetag 7557 becomes very slippery when it comes in contact with water, therefore spills should be cleaned up with an absorbent
material instead of water.

Appearance: White granules

Specific Gravity: 0.80 @ 25°C

Flash Point: >93°C (will burn)

Appearance: Off white powder

Density: 1.5

Moisture Content: <12%

Cal Carb 0 may be added directly at the suction with agitation or through the mud hopper. To avoid settling out in the surface tanks the fluid viscosity should be raised sufficiently to provide adequate suspension. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Cal Carb Supercal - Glass Rock may be added directly through the hopper. To minimize settling in the surface tanks, the fluid should be of sufficient viscosity, or the agitation such that the particles are kept in suspension. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Appearance: Off white powder

Specific Gravity: 1.12

Bulk Density: 1.06 kg/m³

Caustic Soda pH p-Alkalinity
1.00 kg/m³ 8.5 - 9.0 0.1 - 0.25
2.20 kg/m³ 10.0 - 10.5 0.5 - 0.7
2.90 kg/m³ 11.0 - 12.0 0.8 - 1.0
5.80 kg/m³ 14.0 3.0

CF Desco II can be mixed directly through the mud hopper. It is advisable to use a dust mask and eye protection while mixing all powdered products.

CF Desco II may cause irritation to the eyes. If contacted with the eyes, flush immediately with running water for at least fifteen minutes. If irritation develops, seek medical attention.

Although Citric Acid is of low hazard and toxicity, excess exposure to dust should be avoided to prevent irritation to the eyes, skin and respiratory tract. As with all organic material, caution is advised when storing or handling near strong oxidizing agents, alkali metals or strong bases.

Appearance: White granular powder

Bulk Density: 512-560 kg/m³

Appearance: Aromatic amber liquid

Specific Gravity: .916

Bulk Density: 480-560 kg/m³

Flash Point: 18°C

Boiling Point: 83°C

Extra High Yield Bentonite is dry clay and therefore requires high shear and agitation for proper hydration. It should be mixed no faster than five minutes per sack and should always be mixed before polymers. Cold water increases mixing time.

Extra High Yield Bentonite loses effectiveness in hard, low pH or salt water. To achieve the maximum yield of 220-235 bbl, the makeup water should be treated with soda ash (sodium carbonate) to a pH of 8.0-9.0. Do not use salt water since it cannot be treated.

Appearance: Black-brown powder

Specific Gravity: 1.06

Moisture Content: 1.0%

Flash Point: 316%

Appearance: Spherical black particles

Specific Gravity: 1.70 - 1.85

Appearance: Dark brown/black powder

Specific Gravity: 1.5 approx. 

Moisture: 30-35%

Content: 51.9 lbs/ft³

Appearance: White granules

Specific Gravity: 0.80 @ 25°C

Because of its excellent dispersibility and mixing, Hyperdrill AF 247RD can be added directly to the mud system without pre-wetting in a solvent.

A small hole should be cut into the bottom of the bag, allowing it to flow at a steady rate into the mud hopper. If necessary Hyperdrill AF 247RD may be pre-hydrated at concentrations of 10.0-15.0 kg/m³ in a separate tank and fed into the main circulating system to maintain concentrations of 2.0-6.0 kg/m³.

Hyperdrill AF 247RD becomes very slippery when it comes in contact with water. A spill should be cleaned up with an absorbent material. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Appearance: White powder

Bulk Density: 800 - 880 kg/m³

Appearance: White granular powder

Bulk Density: 0.7 kg/m³

Magma Fiber can be mixed through the hopper or added directly to the mud tanks wherever there is adequate agitation. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Magnesium Oxide can be added through the hopper or mixed directly to the system at a point of agitation. It is advisable to use a dust mask and eye protection while mixing Magnesium Oxide or any other powdered material.

Appearance: Off-white powder

Specific Gravity: 1.38 g/cc

Bulk Density: 0.5 - 0.7 g/cc (untamped, tamped)

Appearance: Cream colored powder

Specific Gravity: 1.7

Polythin can be added directly into the mud system through the mixing hopper. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Prima-Seal can be mixed directly into a viscous mud with good agitation. Larger sizes will plug shale shaker screens. If re-circulation is necessary, the shale shaker should be by-passed.

However, bypassing the shaker could result in plugged jets. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Appearance: Black granular

Specific Gravity: 0.7 - 1.11

Flash Point: 320°C

Appearance: Fine white powder

Specific Gravity: 1.862

Bulk Density: 800 kg/m³

Melting Point: 650°C

Appearance: Red wax-like tube

Specific Gravity: 1.07

Melting Point: 49°C

Sodium Bicarbonate can be added directly through the hopper. Avoid inhaling and minimize skin contact. It absorbs moisture and dries the skin. Keep stored in a cool dry place to prevent caking and deterioration. Store away from acids. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Appearance: White crystalline powder

Specific Gravity: 2.63

Appearance: Off-white powder

Bulk Density: 480 - 640 kg/m³

Moisture Content: 6 - 10%

Appearance: Clear liquid

Specific Gravity: 1.0634 @ 15°C

Freezing Point: -6°C

Physical Properties

Chemical Properties

Chemical Properties

Physical Properties

Physical Properties

Mixing & Handling

Physical Properties

Physical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Mixing & Handling

Physical Properties

Chemical Properties

Physical Properties

Non-Oilfield Application

Physical Properties

Physical Properties

Physical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Physical Properties

Physical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Packaging & Controls

Chemical Properties

Chemical Properties

Chemical Properties

Physical Properties

Chemical Properties

Physical Properties

Chemical Properties

Physical Properties

Compressive Strength Development

Physical Properties

Chemical Properties

Chemical Properties

Physical Properties

Chemical Properties

Packaging & Controls

Chemical Properties

Physical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Physical Properties

Physical Properties

Chemical Properties

Physical Properties

Physical Properties

Mixing & Handling

Mixing & Handling

Mixing & Handling

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Physical Properties

Mixing & Handling

Chemical Properties

Chemical Properties

Mixing & Handling

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Hutcheson Sand Mixes

Caps Available

Performance Chart

Performance Chart

Armored 4" HydraSleeve

Physical Properties

Features & Benefits

Optional Accessories

Available Accessories

Optional Item

Optional Features & Items

Optional Item

Requirements

Optional Items

Accuracy

Physical Properties

Physical Properties

Chemical Properties

Packaging & Controls

Packaging & Controls

Mixing & Handling

Chemical Properties

Packaging & Controls

Physical Properties

Chemical Properties

H Sizes Available

H Sizes Available

H Sizes Available

H Sizes Available

H Sizes Available

BTK Sizes Available

P Sizes Available

N Compact Plus Water Swivel Spares Kit and Parts

N Core Barrel Assembly & Options

N Head Assembly & Options

N2 Core Barrel Spares

N Overshot Assembly

Physical Properties

Chemical Properties

Physical Properties

Chemical Properties

Physical & Chemical Properties

AppearanceOff white liquid

Specific Gravity: 1.08 - 1.12

Pour Point: -30°C

Flash Point: 100°C

Type: Blend

Solubility: Dispersible (water)

Microtox: 30% @ 0.5L/m³

Type: Blend

Solubility: Forms suspension (Water)

pH: N/A

Microtox: 1.1 kg/m³

Appearance: Opaque-white liquid

Density: .98 - 1.02 kg/m³

Pour Point: 0°C

Boiling Point: 204 - 371°C

Flash Point: 150°C (closed cup)

Appearance: White powder

Specific Gravity: 0.75 - 0.85

Earth Pro Emul is often used in conjunction with Earth Pro Wet as required by muds with very high solids content. The amount of Earth Pro Emul should always equal or be higher than the amount of Earth Pro Wet used. Employ rubber gloves, rubber apron, and skin and eye protection and ensure mixing is done in an area with adequate ventilation.

Appearance: Clear liquid

Specific Gravity: 0.90

Pour Point: >-20°C

Flash Point: >100°C (TCC)

Appearance: Dark liquid

Specific Gravity: .96

Pour Point: <-20°C

Flash Point: >93.3°C (CC)

Type: Xanthan gum

Solubility: Soluble in water

Type: Ester

Solubility: Not soluble in water

Microtox: >91% @ 0.17 L/m³

Type: Sodium montmorillonite

pH: 9.1 (5% solution)

Property Percentage
Loss on Ignition 4.4%
Silicon Oxide 61.4%
Aluminum Oxide 18.1%
Ferric Oxide 3.5%
Sodium Oxide 2.3%
Magnesium Oxide 1.7%
Calcium Oxide 2.3%
Titanium Oxide 0.2%
Potassium Oxide 0.1%
Water 7.8%
Other 0.07%

Appearance: Free-flowing crystalline

Molecular Weight: 200

Melting Point: 130°C

Appearance: White to cream liquid

Specific Gravity: 1.1

Boiling Point: >100°C

Flash Point: >93°C (PMCC)

Appearance: White powder

Specific Gravity: 0.75 - 1.00

Bulk Density: 800 - 810 kg/m³

Appearance: White powder

Specific Gravity: 1.01

Melting Point: 115-125°C

Barite can be mixed through the mud hopper as rapidly as needed. When large quantities are added to a mud system it may be necessary to add water to prevent mud dehydration.

Appearance: Grey-white-buff powder

Specific Gravity: 2.7 - 2.9

Melting Point: 2570°C

Grind Size: 99.8% passing 5 mesh

Type: Calcium chloride

Solubility: 60% in water

pH: 8.0 - 9.0 (35% solution)

Appearance: White flakes

Specific Gravity: 2.04 @ 20°C

Melting Point: 400°C

Cellophane is used to provide a sealing agent supplement to other lost circulation material in water based drilling muds. It is also a basic additive in cement slurries, providing a matting effect in the control of losses. Typical rates of addition up to 2% by wt. cement are used as a preventative measure.

Appearance: Dark amber liquid

Specific Gravity: 0.86

Pour Point: <-5°C

Flash Point: 75°C

Appearance: Red-brown powder

Specific Gravity: 4.8 - 5.0

Bulk Density: 2400 - 2600 kg/m³

Particle Size: +/- 94-98% passing 74µ

Blaine: 1300-2100 cm²/gram

Appearance: Light colored powder

Specific Gravity: 1.6

Type: Sodium montmorillonite

Solubility: Not soluble (colloidal suspension)

pH: 8.0 - 10.0 (5% solution)

SiO2 61.4% MgO 1.70%
Al2O3 18.1% CaO3 0.40%
Fe2O3 3.50% TiO2 0.20%
K2O 0.10% Na2O 2.30%
H2O 7.80% Other 0.07%
LOS 4.40% (Loss on Ignition)

Type: Organic fiber

Type: Lime-soda glass

Solubility: Not soluble

Type: Amine

Solubility: Dispersible in water

Vapor Pressure (mmHg): 9.98 @ 38°C

Type: Calcium hydroxide

Solubility: 0.165g/100g @ 20°C

pH: 12.45

Type: Flocculant

Solubility: Dispersible-soluble

pH: 6.0 - 8.0 (0.5% solution)

Microtox: >91% @ 3.0 kg/m³

Type: Cationic polyacrylamide

Solubility: Dispersible-soluble

pH: 2.5 - 4.5

Microtox: >91% @ 3.0 kg/m³

Charge Density: 10% molecular

Weight: Medium

Type: Cationic polyacrylamide

Solubility: Dispersible-soluble

pH: 2.5 - 4.5

Type: Xanthan Gum

Solubility: Soluble in water

pH: 7.0 (1% solution)

Type: Cationic polyacrylamide

Solubility: Soluble-dispersible

Charge Density: 10%

Microtox: >91% @ 0.1 L/m³

Type: Anionic alcohol

Solubility: Insoluble

pH: 7.0 - 8.0

Appearance: Light tan-grey powder or granules

Specific Gravity: 2.45 - 2.55

Melting Point: 1450°C

Bulk Density: 49 - 55 lbs/ft³

Appearance: Red/brown powder

Specific Gravity: 0.75

Bulk Density: 600 kg/m³

Type: Salt

Solubility: Soluble in water

pH: 5.4 - 8.6 (5% solution)

Type: Calcium oxide

Solubility: Soluble in water

pH: 12.45 (saturated solution)

Chemical Percentage
Calcium Oxide 95%
Acid Insolubles 1.99%
Magnesium Oxide 1.97%
Loss on Ignition 0.50%

Type: Filming amine

Solubility: Soluble in oil

Microtox: 50% @ 0.5 L/m³

Type: Magnesium silicate

Solubility: Insoluble in water

pH: 7.0 - 8.3

Properties Percentage
Silicone 56.0%
Aluminum 4.0%
Iron 1.0%
Calcium 0.5%
Magnesium 20.0%
Sodium 1.4%
Potassium 1.4%

Type: Chemical compound

Solubility: Soluble (18% @ 21°C)

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pail

Type: Cellulose fluid loss polymer

Solubility: 100% soluble in water 

pH: 6.5 - 8.0

Type: Acid

Solubility: Soluble (22g/100g water @ 20°C)

pH: 1.18 (1% solution)

Type: Potassium Phosphate

Solubility: 187g/100g H20 @ 25°C

pH: 10.2 - 10.7 (1% solution @ 25°C)

Microtox: MTX @ 10kg/m³

Appearance: Light tan fibrous powder

Specific Gravity: .613

Type: Xanthan biopolymer

Solubility: 100% soluble in water

pH: 7.0 (1% solution)

Microtox: >100% @ 6.0 kg/m³

Appearance: White powder

Specific Gravity: 2.7

Bulk Density: 1365 kg/m³

Particle Size Distribution: 87% passing 325 mesh

Type: Alcoholic blend in mineral oil

Solubility: Insoluble in water

Appearance: Greyish white powder

Specific Gravity: 1.60 +/- 0.05 g/cm³

Melting Point: >100°C

Particle Size: Pass 20 mesh > 99.9%

The table below depicts the typical strength development for Earth Pro ResinBond Cement. Using proper mixing and measuring techniques, the typical slurry will remain fluid for 1-1.5 hours after mixing. This time also includes the amount of time required at surface to mix.

Depth Temp Time (Hours)
(m) (°C) 1 1.5 2 3 4 5 6 7 24 48
400 15 Flows Flows Set, No Strength 0.0 0.4 2.1 3.5 6.3 12.6 16.8
600 20 Flows Flows Set, No Strength 0.0 1.8 5.6 7.0 9.1 16.8 19.6
750 25 Flows Flows Set, No Strength 0.0 0.7 2.8 9.8 11.9 15.4 17.5
900 30 Flows Flows Set, No Strength 0.7 2.8 8.1 9.8 11.9 16.1 18.9
1100 35 Flows Flows Set, No Strength 0.5 3.5 10.5 11.2 13.3 14.7 17.5
1300 40 Flows Flows Set, No Strength 1.8 9.5 11.2 12.6 13.3 14.7 20.3
1500 45 Flows Flows Set, No Strength 5.3 13.7 15.4 17.5 18.9 20.3 22.1
1700 50 Flows Flows Set, No Strength 0.0 4.2 5.6 7.7 11.6 16.1 21.0
1900 55 Flows Flows Set, No Strength 0.2 3.9 7.0 8.4 11.9 18.2 22.4
2100 60 Flows Flows Set, No Strength 0.7 4.2 7.7 9.8 13.3 21.7 23.1

Please note that shortly after this open time, the slurry begins the transition to the set state. In all cases, at 2 hours the slurry will no longer flow. This value does vary somewhat depending upon well depth and RB Catalyst loading, so always place the Earth Pro ResinBond Cement plug as quickly and as safely as possible.

The proper amount of clean water, accurate measurement of RB Catalyst, and adequate mixing of the cement all lead to a successful job.

Appearance: Silver grey powder

Specific Gravity: 2.7 (water=1)

Surface Area: 0.34 m²/cm³

Apparent Density: 1.0 g/cc

200 Mesh Retention: Trace

325 Mesh Retention: 11%

Type: Inorganic acid

Solubility: 4.7% w/w @ 20°C

pH: 5.1 (1% w/v in demineralized water)

Type: Blend

Solubility: Soluble in water

Appearance: Tan colored powder

Specific Gravity: 1.247 gm/cm³

Surface Tension: 71 dynes/cm

Type: Modified alkyl sulphonate 100%

pH: 8.0 - 11.4 (20% solution)

WHMIS: Not controlled

TDG: Not regulated

Packaging: 1000L tote

Reducing Sugars: <3%

Sulfur: 7-8%

Sodium: 8-9%

Calcium: <0.1%

Chloride: <0.15%

Appearance: Tan granules

Bulk Density: 840-900 kg/m³

pH: 6.5 - 7.5

Shell Properties

  • Silica: 55-65%
  • Alumina: 25-35%
  • Iron Oxide: <5%

Gas Properties

  • Carbon Dioxide: 65-75%
  • Nitrogen: 25-35%

Type: Powder blend mixture

Solubility: Soluble in water

pH: Slightly basic (1% solution)

Potassium Chloride: 99.47%

Chloride: 47.58%

Sodium: 0.177%

Sodium Chloride: 0.45%

Moisture: 400 ppm

Water Insolubles: 50 ppm

Loss on Ignition: <6.0%

pH: 6.0 - 9.0

Silicon Dioxide: >85%

Type: Chemical compound

Solubility: Soluble 18% @ 21°C

Sodium Carbonate: 99.5% min

Sodium: 58.2% min

Calcium: 150 ppm (max)

Magnesium: 50 ppm (max)

Sodium Sulphate: 400 ppm (max)

Iron: 500 ppm (max)

Moisture: 5 ppm (max)

Water Insolubles: .15% (max) - 500 ppm (max)

Solubility: 15.9% @ 20°C

pH: 8.3 (1% solution)

Sodium Sulphate: 99.1%

Calcium Sulphate: 0.14%

Magnesium Sulphate: 0.50%

Sodium Carbonate: 0.01%

Sodium Chloride: 0.20%

Sodium Bicarbonate: 0.03%

Water Insolubles: 0.02%

Type: Buffer

pH: 12.8

Type: Crosslinker

pH: 11.7

Type: Weighting material

Solubility: Insoluble

pH: 7.0 - 9.5

Appearance: Light tan to grey powder

Specific Gravity: 2.45 - 2.55

Melting Point: >450°C

Slurry Density: 9.4-9.5 lb/gal

Dry Bulk Density: 55-60 lb/ft³

Thermal Conductivity: .42 BTU/hr-ft-°F

Solubility: Not soluble

Appearance: Brown liquid 

Boiling Point: 100°C

Appearance: Light tan to grey powder/granules 

Specific Gravity: 2.45-2.55 

Melting Point: 1450°C

Bulk Density: 49-55 lb/ft³

Mix Earth Pro Claysperse L after mixing regular drilling additives such as viscosifying polymers. Add in batches at the suction side of the mud tank to create a sweep effect in the wellbore.

Earth Pro Claysperse L will thin back most drilling fluids and is most effective when mixed and pumped in only water or in polymer systems. Effectiveness will be reduced in bentonite slurries. When mixing in whole mud do so after the polymer has hydrated.

Under normal drilling conditions if a sticky clay seam is encountered add 2-3 L/m³ of fluid. If a mud ring is suspected add 2 visc cups of Earth Pro Claysperse L directly into the tool joint when making a connection.

In a recycled closed loop system if used as a thinner add sparingly at the front end of the system and check viscosity in the suction end
regularly so as to not over treat.

Earth Pro ProPac D is a dry polymer and should be added slowly through a high shear mixer to prevent lumps or fish eyes. It should not be added before bentonite since the yielded Earth Pro ProPac D will prevent the bentonite from hydrating.

Earth Pro HydraVis L should be mixed at a point of high agitation in the tank to promote even dispersion and hydration. Shake product before opening. Product may have natural separation / settling in liquid form.

Appearance: Yellow and white granules

Specific Gravity: 2.6

Appearance: White granular powder

Granule Density: 0.5

Specific Gravity: 1.5

Required Time: 30 mins for 50% enlargement, 90 mins for 100% enlargement

Appearance: White to off white viscous liquid

Specific Gravity: 1.1

Appearance: Milky, viscous liquid

Specific Gravity: 1.07

Appearance: Black solid

Specific Gravity: 1.04 - 1.08

Flash Point: 310°C

Earth Pro Claymean L is 100% soluble in water and only requires that it be mixed in a manner that allows it to disperse evenly so any kind of agitation is sufficient for proper mixing.

Type: Synthetic polymer blend

Solubility: Partially soluble in water

Fluid Type: Petroleum

Thickener: Calcium complex

Oil Separation, Wt. % Loss @ 100°C: <3.0%

NLGI Grade: 1

Copper Strip Corrosion (ASTM D-4048): 1A, typical

Modified Starch mixes readily and may be added to a mud system through the hopper at 10-15 minutes per bag. It is advisable to use a dust mask and eye protection while mixing all powdered products.

Type: Polyacrylamide

Solubility: Dispersible-Soluble

pH: 6.5 - 7.5 (1% solution)

Microtox: 20% @ 3.0 L/m³

Solubility: 21% soluble in water

pH: 1.18

Volatile Percentage: 34%

Vapor Density: 1.0

Solubility: 100% in water

pH: 7.0

Vapor Density: 1.0

Solubility: 100% in water

pH: 2.4 - 3.4

Grease Carrier: Aluminum complex

Oil Separation, Wt. % Loss: Max 3.0

Water Spray-Off: <8.0%

NLGI Grade: 1.5

Copper Strip Corrosion: 1A

Solubility: 18% by weight of water @ 21°C

Sodium Carbonate: 99.5% min

Sodium: 58.2% min

Calcium: 150 ppm (max)

Magnesium: 50 ppm (max)

Sodium Sulphate: 400 ppm (max)

Sodium Chloride: 500 ppm (max)

Iron: 5 ppm (max)

Moisture: .15% max

Water Insolubles: 500 ppm (max)

pH: 7.0 - 8.0

Viscosity: 20 mPa·s (20°C)

Electrical Conductivity: 30,000 μS/cm

Type: Polyacrylamide

Shelf Life: 6 months when stored @ 5-30°C

Type: Polyacrylamide

Shelf Life: 6 months when stored @ 5-30°C

Product Number Product Name Packaging
27071 Silica Sand 20/40 50lb

Product Number Product Description
47099 QC Slope Indicator Top Cap 70mm (2.75”)
47100 QC Slope Indicator Bottom Cap 70mm (2.75”)
48902 QC Slope Indicator Top Cap 85mm (3.34”)

Factors that affect flow rate include such parameters as the depth of submergence of the foot valve, tubing diameter, well casing diameter, the length of pump stroke and the speed of oscillation of the pump. 

Obviously, the speed of oscillation is the primary factor in imparting momentum to the water column in the pumps tubing. Generally a pumping rate of 100 to 180 strokes per minute is recommended. The recommended stroke length is 4 to 6 inches with a longer stroke performing better in deeper piezometers. 

Greater submergence of the foot valve increases the pressure differential, (the pressure difference between the water within the tubing and the head pressure outside the valve) that is created at the end of the upward pump stroke. Increasing the pressure differential increase the rate of water inflow through the valve at the end of the upward stroke thereby increasing the flow rate. 

Another factor affecting the flow rate with the inertial pump is the size of the annular gap between the Inertial Pump tubing and the ID of the well casing. When the Inertial Pump is operating the flexible tubing will tend to wobble from side to side within the well casing. This wobble results in some of the up and down movement applied at surface to the tubing not reaching the depth where the valve is located. For this reason the stiffer High Density Polyethylene tubing is usually preferred in deeper monitoring wells (depth in excess of 60 – 70 feet). The Inertial Pump performs best in smaller diameter piezometers (4” or less). 

As a general guide, in most 2” monitoring wells, the High Flow System D-32 will usually produce a flow rate of about 1 to 3 gallon per minute given 20 to 30 feet of valve submergence. The High Flow System has a substantial lift capacity in 2” diameter piezometers. Some customers have reported lifts approaching 300 feet.

The Performance Chart shown displays the performance capabilities of the Micro Flow System. This chart is intended to assist you with the selection of the most suitable system for your specific site.

Please note that the ratings have been calculated by actual field testing in a variety of well conditions and therefore may seem somewhat conservative in value.

  • Provides comparable, formation quality samples of ALL parameters from 3" and larger wells for both short and long-term monitoring.
  • Protective outer sleeve more than doubles wall thickness
  • Useful in steel wells, open boreholes, or anywhere a HydraSleeve could come in contact with jagged edges or increased potential for abrasion
  • Disposable
  • Fits in 3" Schedule 40 and larger wells
  • Standard material = virgin 7 mil PE. Tensile strength 25-35 lb
  • Absolute maximum volume obtainable without spilling 1.48 liters
  • Requires the use of 16 oz. Bottom Weight
  • Layflat = 4"W x 30"L
  • Filled Diameter = 2.6"
  • Filled Volume = ~1400 mL
  • Fill Stroke = 30"

Appearance: Clear liquid

Specific Gravity: 0.90

Pour Point: >-20°C

Flash Point: >100°C (TCC)

High Quality Materials

Electric resistance welded alloy steel tubing from American and Japanese suppliers, ensures a uniform wall thickness for greater joint integrity, balanced rotation and even wear.

Di-Corp drill rod is processed with an additional stress relief heat treat, to eliminate bent rods.

A final quench and temper heat treat process is performed before machining the thread to strengthen the rod joint for greater torsional and tensile properties.

Precision Machined Threads

  • Less bulging and breaking
  • Complete line of accessory products are manufactured with the same precision
  • Finished threads are precision machined and not distorted by any other process, providing a superior joint fit with less chance of the joint pulling apart

WARNING: All threads are precision machined and mixing Di-Corp rods with other manufacturers’ rods, adaptors, or threaded accessories is not recommended. Failure to adhere to this recommendation may cause premature failure, an inspection may result in the warranty becoming void.

  • A/C Power Cord, 230 Volt

  • Fuse, 5 Amp, 5 mm × 20 mm Qty.: 5
  • Brush; Graduate ½” × 8” Qty.: 1
  • Graduated Cylinder; 10 mL × 2/10 mL Qty.:1 
  • Lid for 10-mL Sample Cup Qty.:1
  • Spatula Qty.:1 
  • Corkscrew Qty.:1 
  • Steel Wool; Grade 000. Extra Fine; Package of 4 Pads Qty.:16
  • Pipe Cleaner Qty.:6
  • High-Temperature Thread Lubricant; 4-oz. Qty.:1 Tube
  • Wetting Agent Qty.:1

50 mL Receiver Tube for Retort, 2-scales, 0-100% × 0.1, 0-50 mL × 0.1 mL, with certificate

  • 4 - Roller Oven with Redundant Heat Control (115 Volt)
  • 4 - Roller Oven with Redundant Heat Control (230 Volt)
  • Aging Cell, Stainless Steel Grade 303, 260 mL, Pressurized
  • Aging Cell, Stainless Steel Grade 303, 500 mL, Pressurized
  • Aging Cell, Stainless Steel Grade 316, 500 mL, Pressurized
  • Corrosion Test Cell, Stainless Steel Grade 303, 500 mL
  • O-ring for Outside of Aging Cell, Viton
  • CO2 Pressuring Assembly
  • Test Cell Removal and Carrying Tool

  • Cup for Thermocups, Stainless Steel

  • Power: 100 - 240 Volt, 50 - 60 Hz, 2 Amp
  • Computer
    • Windows XP or higher
    • RS-232 Serial Port (or Serial to USB Adapter)
    • Minimum Screen Resolution: 1280 × 680

  • Nitrogen Cylinder, 21” × 7”, Right-hand Thread (shipped empty)
  • Safety Shield
  • HTHP Cell Assembly, Double -capped, HTHP, 500 mL, for Ceramic Disks, 2000 PSI
  • HTHP Cell Cap Puller
  • Test Cell Removal and Carrying Tool
  • HTHP Pressure Relief Tool
  • Safety Clamp for HTHP Fluid Loss Cells

Inclination: +/- 0.15°

Gravity highside: +/- 0.20°

Magnetic toolface: +/- 0.35°

Azimuth: +/- 0.35°

Appearance: White granules

Bulk Density: 1089 kg/m³

Particle Size: 841-212 microns (#20-#65 mesh)

Specific Gravity: 2.5 g/mL

Bulk Density Non-Compacted: 53 lbs/ft³

Bulk Density Compacted: 72 lbs/ft³

200 Mesh Passing: 70% min

Calcium Chloride: 77% min

Sodium Chloride: 6.0% max

Calcium Hydroxide: 0.35% max

Magnesium Chloride: 0.5% max

Water Insoluble: 0.2% max

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb sack/bulk

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb sack/bulk

Enviroplug Tablets should be poured directly into the hole or placed by the tremie method. As with gravel packing, the desired result is a bentonite pack. Therefore, take care in placing the tablets to prevent bridging.

The tablet seal or plug should be placed against an impervious formation, such as clay. Enviroplug Tablets should be allowed to hydrate 1-2 hours before any grout is installed.

A wide variety of sealing products and application methods exist. Please consult local regulations, a groundwater professional or a product
representative prior to commencing any sealing or abandonment procedure.

Granulation (mesh): <200

Solubility: Soluble in water

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb bag

Appearance: White filaments

Softening Point: 315°F

Specific Gravity: 1.0 in treated form

Type: Carbon

Solubility: Negligible

Microtox: 75% @ (6.0 kg/m³)

Part Number Description
102628 HWL Rod Box to Tubing Blank
102629 HD Rod Box to Tubing Blank
102630 HWL Rod Pin to Tubing Blank
102631 HD Rod Pin to Tubing Blank

Part Number Description
100687 HWL Rod Box to NW Rod Pin (Rod to Casing)
102621 HD Rod Box to NW Rod Pin (Rod to Casing)
100687 HWL Rod Box to NW Rod Pin (Rod to Rod)
102621 HD Rod Box to NW Rod Pin (Rod to Rod)

Part Number Description
102615 HWL Rod Box to HD Rod Pin
102616 HD Rod Box to HWL Rod Pin

Part Number Description
100668 AW Rod Pin to HWL Rod Pin (Compact)
102610 AW Rod Pin to HD Rod Pin (Compact)
100594 BW Rod Pin to HWL Rod Pin (Universal)
102611 BW Rod Pin to HD Rod Pin (Universal)

Part Number Description
103037 HWT Casing Bit

Part Number Drilling Parameter Edge Series Waterway Configuration
101632 BTK 6-7 Edge 6 Standard
101635 BTK 6-7 Edge 6 Wide
103402 BTK 7-8 Edge 7 Standard
101633 BTK 6-8 Edge 7 Endurance Standard
101636 BTK 6-8 Edge 7 Endurance Wide
103844 BTK 5-9 Edge 8 Abrasive Standard
102347 BTK 7-9 Edge 8 Endurance Wide
101038 BTK 7-10 Edge 9 Standard
101634 BTK 7-9 Edge 9 Endurance Standard
101637 BTK 7-9 Edge 9 Endurance Wide
103721 BTK 9-10 Edge 10 Standard

Part Number Description
101022 PD (T11) Rod Shoe 
101012 PD (T12) Rod Shoe

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
100613 Core Barrel Assembly, 3 m (10 ft) -
100621 Core Barrel Assembly, 1.5 m (5 ft) -
100769 Locking Coupling, Conventional, Tang
100542 Adaptor Coupling
100439 Landing Ring 1
100545 Outer Tube, 3 m (10 ft) 1
100588 Outer Tube, 1.5 m (5 ft) -
100443 Inner Tube Stabilizer 1
100476 Head Assembly 1
100544 Inner Tube, 3 m (10 ft) 1
100587 Inner Tube, 1.5 m (5 ft) -
100417 Stop Ring 1
100415 Core Lifter, Slotted 1
100416 Core Lifter Case 1

 

Options
Part Number Description
101542 Locking Coupling, Conventional, No Tang
100616 Locking Coupling, Full Hole, Tang
100741 Locking Coupling, Full Hole, No Tang
100423 Core Lifter, Fluted
100418 Core Lifter, Smooth
100845 Core Lifter, Slotted, Diamond Coated
100848 Core Lifter, Fluted, Diamond Coated
100780 Outer Tube 3 m (10 ft) C/P
100779 Outer Tube 1.5 m (5 ft) C/P
100788 Inner Tube 3 m (10 ft) C/P
100787 Inner Tube 1.5 m (5 ft) C/P
101100 Core Barrel Plug

Part Number Description Qty
100476 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100464 Spearhead Base 1
100449 Latch Retracting Pin 2
100465 Latch Retracting Case 1
100466 Upper Latch Body 1
100451 Latch Pivot Pin 1
100450 Latch Spring 1
100808 Latch  2
100469 Landing Shoulder 1
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 1
100470 Lower Latch Body 1
100453 Lock Washer 1
100454 Hex Nut 1
100471 Spindle 1
100455 Shut Off Valve, Hard 2
100456 Shut Off Washer 2
100457 Spindle Bearing, Upper 1
100472 Spindle Bushing 1
100458 Spindle Bearing, Lower 1
100459 Compression Spring 1
100460 Self Locking Nut 1
100475 Inner Tube Cap Assembly without Thread Protector 1
100602 Thread Protector 1

 

Options
Part Number Description
100551 Landing Indicator Bushing without OD Groove
100583 Shut Off Valve, Soft
101819 Solid Spindle Spacer
101152 Parts Pouch
101822 Inner Tube Cap Assembly with Thread Protector
100607 Fluid Retention Kit

Part Number Description Qty
103232 Core Barrel Spares Kit -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Coiled Spring Pin, ø7/16" x 1" Long 2
100449 Latch Retracting Pin 2
100450 Latch Spring 2
100808 Latch 4
100451 Latch Pivot Pin 2
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 2
100553 Landing Shoulder 1
100454 Hex Nut 1
100455 Shut Off Valve, Hard 4
100457 Bearing, Upper 1
100458 Bearing, Lower 1
100460 Self Locking Nut 1
100461 Grease Fitting 2
100434 Stop Ring 2
100424 Core Lifter, Slotted 20
100429 Core Lifter Case 4
100440 Landing Ring 1
100444 Inner Tube Stabilizer 2

Part Number Description Qty
100517 Overshot Assembly -
100604 Overshot Head Assembly -
100518 Cable Swivel Eye Bolt 1
100519 Cable Swivel Collar 1
100520 Thrust Bearing 1
100521 Castle Nut 1
100522 Cotter Pin 1
100461 Grease Fitting 1
100523 Cable Swivel Body 1
100524 Jar Staff 1
100525 Jar Tube Assembly 1
100534 Locking Sleeve 1
100526 Hex Nut, 3/4" UNC 1
100527 Nord-Lock Washer 1
100528 Overshot Head Body 1
100533 Set Screw 1
100529 Compression Spring, Lifting Dog 1
100530 Lifting Dog 2
100531 Lifting Dog Pivot Pin 1
100532 Sway Pin 1
100535 Pin Link 2
100539 Self Locking Cap Screw 4
100692 Overshot Loading Fork Tool 1
100689 Overshot Loading Funnel 1

Appearance: Opaque liquid

Bulk Density: 1010 kg/m3

Type: Hydrocarbon

Solubility: Soluble in hydrocarbons

Appearance: Yellow to brown liquid

Specific Gravity: 1.1

Pour Point: -15°C

Flash Point: 152°C

Boiling Point: 249°C

Type: Bactericide

Solubility: Soluble (100% in water)

pH: 3.6

Appearance: Grey Tan Powder

Viscosity Yield: 185-200 bbls

Packaging: 22.68kg, 50lb plastic lined paper bag

Chemical Properties

Packaging & Controls

Packaging & Controls

Chemical Properties

Chemical Properties

Physical Properties

Chemical Properties

Chemical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Physical Properties

Chemical Properties

Chemical Properties

Mixing & Handling

Chemical Properties

Chemical Properties

Chemical Properties

Typical Toxicity Analysis

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Chemical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Packaging & Controls

Chemical Properties

Field Mixing Procedure

Chemical Properties

Packaging & Controls

Packaging & Controls

Chemical Properties

Packaging & Controls

Packaging & Controls

Chemical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Chemical Properties

Packaging & Controls

Chemical Properties

Physical Properties

Physical Properties

Physical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Chemical Properties

Physical Properties

Packaging & Controls

Packaging & Controls

Physical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Identification

Optional Tools

Capacity

Accessories

Chemical Properties

Chemical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

P Sizes Available

P Sizes Available

P Sizes Available

P Sizes Available

P Sizes Available

N Sizes Available

N2 Compact Plus Water Swivel Spares Kit and Parts

N2 Core Barrel Assembly & Options

N2 Head Assembly & Options

N2 Overshot Assembly

Packaging & Controls

Chemical Properties

Packaging & Controls

Packaging & Controls

Type: Synthetic polymer emulsion

Solubility: Dispersable - soluble

pH: 6.5 - 7.5 (1.0% solution)

Character: HMW anionic 

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L and 60L pails

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg bag

Type: Silicone emulsion

Solubility: Dispersible in water

Viscosity: 1700 (Brookfield RVT, #3 Spindle, 50 RPM) @ 27°C

Microtox: >75% @ 0.5 L/m³

Type: Water soluble polymer

Solubility: Soluble in water

pH: 7.0 - 7.5 (1% solution)

Microtox: 2.35 kg/m³

Appearance: Amber liquid

Specific Gravity: .91

Pour Point: <-20°C

Flash Point: >93°C (PMCC)

Type: Clay inhibitor

Solubility: 100% soluble in water

pH: >12.0

Microtox: 16.0 L/m³

Type: Dispersant

Solubility: Soluble in oil

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pail

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 210L drum

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 40kg sack

Type: Bactericide

Solubility: Soluble in water

pH: 5.0 - 7.0 (1% @20°C)

Microtox: 10% @ .03 kg/m³

Type: Shale inhibitor

Solubility: Soluble in water

pH: 7.5 (1% solution)

Type: Cationic polyacrylamide

Molecular Weight: Medium

Charge Density: 10%

Solubility: Soluble-Dispersible

pH: 3.5 - 4.5 (1% solution)

Type: Defoamer

Solubility: 3.0 - 4.0 (5% dispersion)

Microtox: 7% @ 0.285 kg/m³

Appearance: Grey-white powder

Specific Gravity: 4.2 - 4.4

Moisture Content: 1580°C

Type: Mineral

Solubility: 1.3 mg/100g @ 18°C

pH: 8.3 - 9.7 (1% solubility)

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 80lb sack

Type: Alkali hydroxide

Solubility: Soluble (water)

pH: 12.0 (0.01 moles/liter)

Oilfield and Non-Oilfield: Mix into a viscous mud with agitation. Cellophane will not pass through the shaker screen. In order to maintain the Cellophane concentration in the mud the shale shaker must be by-passed. Note: Bypassing the shaker could result in plugged jets.

Cementing: Add the Cellophane to the cement slurry in the mix tub prior to displacement. No special mixing precautions are required when mixing Cellophane. Care should be taken to avoid mixing the product too quickly as Cellophane will have tendency to plug lines.

Type: Carbon

Solubility: Soluble in oil

Type: Iron oxide

Solubility: Insoluble

pH: 6.5 - 8.0

FE2O3: 95.6 - 98%

Moisture: <0.5%

Type: Cellulose fluid loss polymer

pH: 6.5 - 8.0

Microtox: 100% @ 3.0 kg/m³

  Standard (ppm) Set Grout (ppm)
Arsenic 5.0 <0.10
Barium 100.0 0.50
Cadmium 1.0 <0.05
Chromium 5.0 <0.10
Lead 5.0 <0.10
Mercury 0.2 <0.02
Selenium 1.0 <0.05
Silver 5.0 <0.10

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25lb bag

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb sack

WHMIS: Controlled (see MSDS)

TDG: Regulated

Packaging: 20L pail

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg sack

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg bag

WHMIS: Controlled (see MSDS)

TDG: Not regulated 

Packaging: 25kg bag

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 30kg bag

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg sack

Solubility: 100% soluble in water

pH: 8.0 - 10.0 (5% aq. solution)

Chemical Percentage
Silicone Oxide (SiO2) 61%
Aluminum Oxide (AlO3) 18.1%
Ferric Oxide (Fe2O3) 3.5%
Sodium Oxide (Na2O) 2.3%
Magnesium Oxide (MgO) 1.7%
Calcium Oxide (CaO) 0.2%
Titanium Oxide (TiO2) 0.1%
Potassium Oxide (K2O) 0.07%
Other 7.8%

Type: Synthetic sulfonated

Solubility: Soluble in water

pH: 7.0 - 9.0 (150 g/L @ 20°C)

Microtox: >91% @ 11.4 kg/m³

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pail

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg bag/bulk

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pail

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25-40lb sack

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb sack

WHMIS: Controlled (see MSDS)

TDG: Regulated

Packaging: 25kg sack

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb sack

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg sack

Water Requirement: 40% w/w

pH: 6.0 - 8.0 (10% solution)

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pail

Type: Proprietary mixture

Solubility: Moderate in water

pH: 6.0 - 8.0 (1% solution)

  1. Obtain as much well information as possible for the Earth Pro ResinBond Cement plug, most important are depth, and/or BHST (°C.)
  2. Ensure well has been circulated clean, and that the well is dead.
  3. Measure accurately the correct amount of CLEAN, FRESH water into the mixing vessel. Five (5) liters of water per 20 kg pail of Earth Pro ResinBond Cement is required for proper hydration. Do NOT use produced or contaminated water sources for mixing Earth Pro ResinBond Cement. Uncontrollable slurry properties could result in job failure. Ensure the mixing water temperature is 15-25°C. Lower temperature water may result in difficulty mixing, while using very hot water may lead to loss of working time, again leading to job failure.
  4. In the following table, find the temperature closest to the BHT in the well being serviced. This corresponds to the proper amount of RB Catalyst L PER PAIL of Earth Pro ResinBond Cement required in this well situation.
  5. Carefully pour the required amount of RB Catalyst into the measuring vial. Shake lightly to level. Re-measure and add or remove Catalyst as required. Do NOT tamp, as product will compact, leading to overt treating. Slight overdosing or under dosing will not compromise the overall fluid properties of Earth Pro ResinBond Cement, but care in handling is always recommended.
  6. Add the required amount of RB Catalyst L FIRST to the mixing water. Stir for a minimum of 3-5 minutes to ensure proper dissolution.
  7. Add the Earth Pro ResinBond Cement to the water and RB Catalyst L while mixing steadily to avoid lumping, and mix until the slurry is visibly smooth.
  8. Pour into the dump bailer equipment and run to bottom and place plug as per usual procedure.
  9. Pull up slowly to avoid disturbing plug.
  10. Apply squeeze pressure if required.
RB Catalyst L Loading
Depth Temp Catalyst L per 20 kg Measured Volume per 20 kg
(m) (°C) (grams) (cc)
400 15 280 Full container
600 20 220 200
750 25 170 150
900 30 150 130
1100 35 130 110
1300 40 90 75
1500 45 60 45
1700 50 20 15
1900 55 20 15
2100 60 20 15

NOTE: Temperatures are estimates for average Western Canadian well conditions and are for reference purposes only. Please contact oil company personnel for specific well depth/temperature profiles in the area for accuracy.

Aluminum: 99.5%

Silicon: <1.0%

Iron: <1.0%

Solubility: Soluble in water

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg/50lb bags

WHMIS: Controlled (see MSDS)

TDG: Regulated

Packaging: 20L pail

Sodium Napthalene Sulphonate: 85%

Sodium Sulphate: 10%

Water: 5%

Solubility: Soluble in water

pH: 9.5 (1% solution)

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb bag

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg bag

Solubility: Soluble in water

pH: 14.0 (1% in fresh water)

WHMIS: Not controlled

TDG: Not regulated

Packaging: 1700lb bag / bulk

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg pail

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg bag

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg bag 

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25-40kg sack

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb bag

WHMIS: Controlled (see MSDS)

TDG: Regulated

Packaging: 1000L tote

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 1000L tote

WHMIS: Not controlled

TDG: Not regulated

Packaging: 40kg bag

Type: Montmorillonite; bentonite

Solubility: Insoluble

pH: 8.0 - 11.0 (5% solution)

pH: 8.0-10.0

Typical Chemical Analysis
SiO2 63.54% MgO 1.67%
Al2O3 19.28% CaO3 0.38%
Fe2O3 3.48% TiO2 0.22%
K2O 0.10% Na2O 2.34%
MnO 0.02% H2O 4.50%
LOS 4.37% (Loss on Ignition) 

WHMIS: Controlled (see MSDS

TDG: Not regulated 

Packaging: 17kg pail

Type: Natural mineral, montmorillonite

Solubility: Insoluble, forms colloidal suspension

pH: 8.0 - 10.0 (5% aq. suspension)

Appearance: Amber liquid

Concentration: 0.25-3L/m³

Appearance: Tan powder

Appearance: Tan powder

Type: Synthetic polymer blend

Solubility: Partially in water

pH: 8.0

Type: Swelling polyacrylamide

Ionic Charge: Anionic

Solubility: Insoluble in water

Type: Synthetic polymer

Ionic Charge: Anionic

Solubility: Soluble in water

Solubility: Miscible in water

pH: 6.0 - 8.0 (5 g/L)

Solubility: Insoluble

Specific Gravity: 1.15

Pour Point: < -35°C

Flash Point: > 100°C

Boiling Point: >100°C

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail

WHMIS: Not controlled

TDG: Not regulated

Packaging: 5 gal pail

Appearance: Off-white powder

Bulk Density: 480-640 kg/m³

Moisture Content: 6-10%

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pail

WHMIS: Controlled (see MSDS)

TDG: Regulated

WHMIS: Not controlled

TDG: Not regulated

WHMIS: Not controlled

TDG: Not regulated

WHMIS: Not controlled

TDG: Not regulated

Packaging: 5L pail

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg / 40kg bag or 50lb pail 

WHMIS: Not controlled

TDG: Not regulated

Packaging: 1000L tote

WHMIS: Not controlled

TDG: Not regulated

Packaging: bulk / 1000L totes

WHMIS: Not controlled

TDG: Not regulated

Packaging: bulk / 1000L totes

Type: Clay inhibitor

Solubility: 100% soluble in water

pH: >12.0

Microtox: 16.0 L/m³

  • Pin ends are stamped with a code for easy traceability
  • Standard wireline drill rods have NO identification grooves
  • End cap decals are used to identify the product once packaged for shipping

  • 10 mL Receiver Tube for Retort, 2-scales, 0-100% X 0.1, 0-10 mL X 0.1 mL, with certificate 2
  • 20 mL Retort Chamber with Lid (functional with 10 mL Retort Condenser

  260 mL Aging Cells 500 mL Aging Cells 1 L Aging Cells
4 Roller Oven 6 3 3
5 Roller Oven 12 6 4

Solubility: 180 kg/m³ @ 20°C

pH: 12.6 (1% solution)

Sodium Oxide: 50.5%

Silicon Dioxide: 46.2%

Carbon Dioxide: 1.66% max

Insolubles: 0.02% max

Iron: 15 ppm max

Moisture: 9.3%

Free Swell: 28 mL

Plate Water Absorption: 776.55%

Grit % (<75 micron): 3.0%

WHMIS: Controlled (see MSDS)

TDG: Regulated

Packaging: 40kg bag

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb pail

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg bag

WHMIS: Not controlled

TDG: Not regulated

Packaging: 15lb boxes / pails

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb sack

Part Number Description
102641 PD Rod (HWT Casing) Box to Tubing Blank
102642 PD Rod (HWT Casing) Pin to Tubing Blank

Part Number Description
102637 PD Rod (HWT Casing) Box to NW Rod Pin (Rod to Casing)
102637 PD Rod (HWT Casing) Box to NW Rod Pin (Rod to Rod)

Part Number Description
102248 PD Rod (HWT Casing) Box to PW Casing Pin
100678 PD Rod (HWT Casing) Box to PWT Casing (SD Rod) Pin
102635 PW Casing Box to PWT Casing (SD Rod) Pin
102636 PWT Casing (SD Rod) Box to PW Casing Pin

Part Number Description
101860 AW Rod Pin to PD (HWT Casing) Rod Pin (Compact)
102632 BW Rod Pin to PD (HWT Casing) Rod Pin (Universal)

Part Number Description
103151 PWT Casing Bit

Part Number Drilling Parameter Edge Series Waterway Configuration
101263 N 2-4 Edge 2 Abrasive Superflush
101216 N 2-4 Edge 2 Abrasive Wide
100958 N 4-6 Edge 5 Standard
101264 N 4-6 Edge 5 Superflush
100959 N 4-6 Edge 5 Wide
101214 N 6-7 Edge 6 Standard
101670 N 6-7 Edge 6 Superflush
101217 N 6-7 Edge 6 Wide
101846 N 6-8 Edge 6 Abrasive Standard
102303 N 6-8 Edge 6 Abrasive Superflush
102305 N 6-8 Edge 6 Abrasive Wide
101573 N 7-8 Edge 7 Standard
103162 N 7-8 Edge 7 Superflush
101666 N 7-8 Edge 7 Wide
100906 N 6-8 Edge 7 Endurance Standard
100907 N 6-8 Edge 7 Endurance Superflush
101233 N 6-8 Edge 7 Endurance Wide
101698 N 7-8 Edge 8 Standard
101973 N 7-8 Edge 8 Wide
103772 N 5-9 Edge 8 Abrasive Standard
103773 N 5-9 Edge 8 Abrasive Superflush
103501 N 5-9 Edge 8 Abrasive Wide
101863 N 7-9 Edge 8 Endurance Standard
102410 N 7-9 Edge 8 Endurance Superflush
102104 N 7-9 Edge 8 Endurance  Wide
100853 N 7-10 Edge 9 Standard
100858 N 7-10 Edge 9 Superflush
100931 N 7-10 Edge 9 Wide
101036 N 7-9 Edge 9 Endurance Standard
101660 N 7-9 Edge 9 Endurance Superflush
101234 N 7-9 Edge 9 Endurance Wide
101002 N 9-10 Edge 10 Standard
103851 N 9-10 Edge 10 Superflush
102306 N 9-10 Edge 10 Wide

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
100614 Core Barrel Assembly, 3 m (10 ft) -
100622 Core Barrel Assembly, 1.5 m (5 ft) -
100769 Locking Coupling, Conventional, Tang
100542 Adaptor Coupling
100440 Landing Ring 1
100545 Outer Tube, 3 m (10 ft) 1
100588 Outer Tube, 1.5 m (5 ft) -
100444 Inner Tube Stabilizer 1
100555 Head Assembly 1
100550 Inner Tube, 3 m (10 ft) 1
100626 Inner Tube, 1.5 m (5 ft) -
100434 Stop Ring 1
100424 Core Lifter, Slotted 1
100429 Core Lifter Case 1

 

Options
Part Number Description
101542 Locking Coupling, Conventional, No Tang
100616 Locking Coupling, Full Hole, Tang
100741 Locking Coupling, Full Hole, No Tang
100425 Core Lifter, Fluted
100641 Core Lifter, Smooth
100846 Core Lifter, Slotted, Diamond Coated
100849  Core Lifter, Fluted, Diamond Coated
100780 Outer Tube 3 m (10 ft) C/P
100779 Outer Tube 1.5 m (5 ft) C/P
101688 Inner Tube 3 m (10 ft) C/P
101852 Inner Tube 1.5 m (5 ft) C/P
100645 Core Barrel Plug

Part Number Description Qty
100555 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100464 Spearhead Base 1
100449 Latch Retracting Pin 2
100465 Latch Retracting Case 1
100466 Upper Latch Body 1
100451 Latch Pivot Pin 1
100450 Latch Spring 1
100808 Latch  2
100469 Landing Shoulder 1
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 1
100553 Landing Shoulder 1
100470 Lower Latch Body 1
100453 Lock Washer 1
100454 Hex Nut 1
100471 Spindle 1
100455 Shut Off Valve, Hard 2
100456 Shut Off Washer 2
100457 Spindle Bearing, Upper 1
100472 Spindle Bushing 1
100458 Spindle Bearing, Lower 1
100459 Compression Spring 1
100460 Self Locking Nut 1
100556 Inner Tube Cap Assembly without Thread Protector 1

 

Options
Part Number Description
100551 Landing Indicator Bushing without OD Groove
100583 Shut Off Valve, Soft
101819 Solid Spindle Spacer
101152 Parts Pouch
100607 Fluid Retention Kit

Part Number Description Qty
100517 Overshot Assembly -
100604 Overshot Head Assembly -
100518 Cable Swivel Eye Bolt 1
100519 Cable Swivel Collar 1
100520 Thrust Bearing 1
100521 Castle Nut 1
100522 Cotter Pin 1
100461 Grease Fitting 1
100523 Cable Swivel Body 1
100524 Jar Staff 1
100525 Jar Tube Assembly 1
100534 Locking Sleeve 1
100526 Hex Nut, 3/4" UNC 1
100527 Nord-Lock Washer 1
100528 Overshot Head Body 1
100533 Set Screw 1
100529 Compression Spring, Lifting Dog 1
100530 Lifting Dog 2
100531 Lifting Dog Pivot Pin 1
100532 Sway Pin 1
100535 Pin Link 2
100539 Self Locking Cap Screw 4
100692 Overshot Loading Fork Tool 1
100689 Overshot Loading Funnel 1

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb bag

Type: Blend

Solubility: Soluble in water and brine

pH: 12.0 (neat)

WHMIS: Controlled (MSDS available)

TDG: Regulated

Packaging: 20L pail, 1000L tote

 

Packaging & Controls

Packaging & Controls

Chemical Properties

Packaging & Controls

Packaging & Controls

Chemical Properties

Packaging & Controls

Packaging & Controls

Physical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Physical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Chemical Properties

Chemical Properties

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Packaging & Controls

Chemical Properties

Chemical Properties

Packaging & Controls

Packaging

N3 Compact Plus Water Swivel Spares Kit and Parts

N3 Core Barrel Assembly & Options

N3 Head Assembly & Options

N3 Overshot Assembly

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20L pails

WHMIS: Not controlled

TDG: Not regulated

Packaging: 15kg sack

Type: Blend of surface active agents

pH: 7.0 - 8.0

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: Fiber keg, 25-1kg water-soluble bags in poly packages

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 20kg pail

Type: Inorganic barium salt

Solubility: Insoluble (water, oil)

pH: 7.0 - 9.5

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg sack

Appearance: Polycellulose clear flakes

Specific Gravity: 1.0

Bulk Density: 140 kg/m³ loose

Average Flake Size: 9.5mm

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 200L drum

WHMIS: Not controlled

TDG: Not regulated

Packaging: 100lb sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb sack

WHMIS: Not controlled

TDG: Not regulated

Packaging: 25kg sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 25kg bag

Appearance: White powder

Composition: Blend

Density: 2.3 - 2.5 g/cc

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb sack

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb bag / bulk

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb sack / bulk

WHMIS: Controlled (see MSDS)

TDG: Not regulated

Packaging: 50lb sack 

Type: Synthetic polymer

pH: 7.0-7.5

Solubility: Soluble in water

Ionic Charge: Cationic

Type: Poly anionic cellulose

Ionic Charge: Anionic

Solubility: Soluble in water

Microtox: 10kg/m³

Type: Natural long chain polymer

Solubility: Soluble in water

Ionic Charge: Slightly anionic

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail 

WHMIS: Not controlled

TDG: Not regulated

Packaging: 50lb bag

Type: Amine salts

Solubility: Miscible 100% in water

Ionic Charge: Slightly cationic

pH: 8.0

Type: Modified polysaccharide

Solubility: Soluble in water

pH: 9.0 - 10.5

Microtox: 10.68 kg/m³

WHMIS: Not controlled

TDG: Not regulated

Packaging: 1000L tote

  • All rods are packaged and sold in bundles
  • The entire length of the rod is coated with Krown rust protection oil
  • Box and pin ends are protected with plastic end caps to ensure the anti-galling thread compound does not get contaminated or removed before first use
  • Hexagonal bundle end caps further protect the rod ends during shipping and make them easier to stack

Packaging & Shipping Information - Drill Rod

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
101790 Core Barrel Assembly, 3 m (10 ft) -
101791 Core Barrel Assembly, 1.5 m (5 ft) -
100769 Locking Coupling, Conventional, Tang 1
100542 Adaptor Coupling 1
100439 Landing Ring 1
100545 Outer Tube, 3 m (10 ft) 1
100588 Outer Tube, 1.5 m (5 ft) -
100443 Inner Tube Stabilizer 1
100476 Head Assembly 1
100544 Inner Tube, 3 m (10 ft) 1
100587 Inner Tube, 1.5 m (5 ft) -
101787 Stop Ring* 1
101780 Core Lifter, Fluted* 1
101144 Core Lifter Case* 1

*These items are exclusive to the triple tube system, all other items are common with the standard double tube core barrel system.

Pump Out Group*
Part Number Description Qty
101794 Pump-Out Adaptor 1
101370 Piston Plug 1
101381 O-Ring 1
101380 Core Ejection Piston 1
101366 Split Tube, 3 m (10 ft) 1
101711 Split Tube, 1.5 m (5 ft) -

 

Options
Part Number Description
101542 Locking Coupling, Conventional, No Tang
100616 Locking Coupling, Full Hole, Tang
100741 Locking Coupling, Full Hole, No Tang
101789 Core Lifter, Fluted, Diamond Coated
101716 Core Barrel Plug

Part Number Description Qty
100476 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100464 Spearhead Base 1
100449 Latch Retracting Pin 2
100465 Latch Retracting Case 1
100466 Upper Latch Body 1
100451 Latch Pivot Pin 1
100450 Latch Spring 1
100808 Latch  2
100469 Landing Shoulder 1
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 1
100470 Lower Latch Body 1
100453 Lock Washer 1
100454 Hex Nut 1
100471 Spindle 1
100455 Shut Off Valve, Hard 2
100456 Shut Off Washer 2
100457 Spindle Bearing, Upper 1
100472 Spindle Bushing 1
100458 Spindle Bearing, Lower 1
100459 Compression Spring 1
100460 Self Locking Nut 1
100475 Inner Tube Cap Assembly without Thread Protector 1
100602 Thread Protector 1

 

Options
Part Number Description
100551  Landing Indicator Bushing without OD Groove
100583  Shut Off Valve, Soft
101819  Solid Spindle Spacer
101152  Parts Pouch
101822  Inner Tube Cap Assembly with Thread Protector
100607  Fluid Retention Kit

Part Number Description Qty
100517 Overshot Assembly -
100604 Overshot Head Assembly -
100518 Cable Swivel Eye Bolt 1
100519 Cable Swivel Collar 1
100520 Thrust Bearing 1
100521 Castle Nut 1
100522 Cotter Pin 1
100461 Grease Fitting 1
100523 Cable Swivel Body 1
100524 Jar Staff 1
100525 Jar Tube Assembly 1
100534 Locking Sleeve 1
100526 Hex Nut, 3/4" UNC 1
100527 Nord-Lock Washer 1
100528 Overshot Head Body 1
100533 Set Screw 1
100529 Compression Spring, Lifting Dog 1
100530 Lifting Dog 2
100531 Lifting Dog Pivot Pin 1
100532 Sway Pin 1
100535 Pin Link 2
100539 Self Locking Cap Screw 4
100692 Overshot Loading Fork Tool 1
100689 Overshot Loading Funnel 1

Packaging & Controls

Packaging & Controls

NU Compact Plus Water Swivel Spares Kit and Parts

NU Core Barrel Assembly & Options

NU Head Assembly & Options

NU Overshot Assembly

WHMIS: Not controlled

TDG: Not regulated

Packaging: 20L pail

WHMIS: Not controlled

TD: Not regulated

Packaging: 20L pail

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
100795 Core Barrel Assembly, 3 m (10 ft) -
100794 Core Barrel Assembly, 1.5 m (5 ft) -
101542 Locking Coupling, Conventional, No Tang
100766 Drive Coupling
100439 Landing Ring 1
100545 Outer Tube, 3 m (10 ft) 1
100588 Outer Tube, 1.5 m (5 ft) -
100443 Inner Tube Stabilizer 1
100791 Head Assembly 1
100544 Inner Tube, 3 m (10 ft) 1
100587 Inner Tube, 1.5 m (5 ft) -
100417 Stop Ring 1
100415 Core Lifter, Slotted 1
100416 Core Lifter Case 1

 

Options
Part Number Description
100741 Locking Coupling, Full Hole, No Tang
100551 Landing Indicator Bushing, No OD Groove
100583 Shut-Off Valve, Soft
101819 Solid Spindle Spacer
101822 Inner Tube Cap Assembly, With Thd. Protector
100632 Inner Tube Coupling
100552 Inner Tube Extension, Stabilized (10") Shell
100903 Inner Tube Extension, Double Stabilized (18") Shell
100423 Core Lifter, Fluted
100845 Core Lifter, Slotted, Diamond Coated
100848 Core Lifter, Fluted, Diamond Coated
100418 Core Lifter, Smooth
100645 Graphite Core Barrel Plug
101105 Gauge Assembly, Bit & Shell
100780 Outer Tube, Chrome Plated, 3.0 m (10 ft)
100779 Outer Tube, Chrome Plated, 1.5 m (5 ft)
100788 Inner Tube, Chrome Plated, 3.0 m (10 ft)
100787 Inner Tube, Chrome Plated, 1.5 m (5 ft)
101152 Parts Pouch
100607 Fluid Retention Kit

Part Number Description Qty
100791 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100796 Spearhead Base 1
100798 Latch Locking Spring 1
100805 Latch Locking Pin 1
100449 Latch Retracting Pin 2
100797 Latch Retracting Case 1
100807 Latch Retracting Case Pin 1
100804 Latch Body, Upper 1
100451 Latch Pivot Pin 1
100450 Latch Spring 1
100808 Latch 2
100827 Spring Seat 1
100801 Latch Retracting Case Spring 1
100826 Spring Sleeve 1
100828 Spring Cavity Bushing 1
100809 Latch Body Adaptor 1
100764 Pump-In Seal 2
100810 Latch Body Seal Seat 1
100452 Stainless Steel Ball 1
100468 Landing Indicator Bushing, OD Groove 1
100469 Landing Shoulder 1
100470 Latch Body, Lower 1
100453 Nord-Lock Washer 1
100454 Lock Nut 1
100471 Spindle 1
100455 Shut-Off Valve, Hard 2
100456 Shut-Off Washer 2
100457 Spindle Bearing, Upper 1
100472 Spindle Bushing 1
100458 Spindle Bearing, Lower 1
100459 Compression Spring 1
100460 Self Locking Hex Nut 1
100475 Inner Tube Cap Assembly, No Thd. Protector 1
100602 Thread Protector, Inner Tube Cap 1

 

Part Number Description Qty
100842 Overshot Assembly -
100518 Cable Swivel Eye Bolt 1
100519 Cable Swivel Collar 1
100520 Thrust Bearing 1
100521 Castle Nut 1
100522 Cotter Pin 1
100461 Grease Fitting 1
100836 Cable Swivel Body 1
100838 Shear Pin 1
100837 Upper Body 1
100764 Pump-In Seal 2
100810 Latch Body Seal Seat 1
100452 Stainless Steel Ball 2
100468 Landing Indicator Bushing, OD Groove 1
100839 Overshot Head Body 1
100529 Compression Spring 1
100840 Pivot Pin 1
100841 Sway Pin 1
100530 Lifting Dog 2

N2U Compact Plus Water Swivel Spares Kit and Parts

N2U Head Assembly & Options

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
100932 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100796 Spearhead Base 1
100798 Latch Locking Spring 1
100805 Latch Locking Pin 1
100449 Latch Retracting Pin 2
100797 Latch Retracting Case 1
100807 Latch Retracting Case Pin 1
100804 Latch Body, Upper 1
100451 Latch Pivot Pin 1
100450 Latch Spring 1
100808 Latch 2
100827 Spring Seat 1
100801 Latch Retracting Case Spring 1
100826 Spring Sleeve 1
100828 Spring Cavity Bushing 1
100809 Latch Body Adaptor 1
100764 Pump-In Seal 2
100810 Latch Body Seal Seat 1
100452 Stainless Steel Ball 1
100468 Landing Indicator Bushing, OD Groove 1
100553 Landing Shoulder 1
100470 Latch Body, Lower 1
100453 Nord-Lock Washer 1
100454 Lock Nut 1
100471 Spindle 1
100455 Shut-Off Valve, Hard 2
100456 Shut-Off Washer 2
100457 Spindle Bearing, Upper 1
100472 Spindle Bushing 1
100458 Spindle Bearing, Lower 1
100459 Compression Spring 1
100460 Self Locking Hex Nut 1
100475 Inner Tube Cap Assembly 1

 

H Compact Plus Water Swivel Spares Kit and Parts

H Head Assembly & Options

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
101407 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100493 Spearhead Base 1
100483 Latch Retracting Pin 2
101394 Latch Retracting Case 1
101395 Upper Latch Body 1
100484 Latch Pivot Pin 1
100450 Latch Spring 1
100496 Latch  2
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 1
100497 Landing Shoulder 1
100498 Lower Latch Body 1
100485 Lock Washer 1
100486 Hex Nut 1
100499 Spindle 1
100487 Shut Off Valve, Hard 2
100488 Shut Off Washer 2
100489 Spindle Bearing, Upper 2
100500 Spindle Bushing 1
100457 Spindle Bearing, Lower 1
100491 Compression Spring 1
100492 Self Locking Nut 1
100502 Inner Tube Cap Assembly without Thread Protector 1
100603 Thread Protector, Inner Tube Cap 1

 

Options
Part Number Description
100551 Landing Indicator Bushing without OD Groove
100584 Shut Off Valve, Soft
101435 Solid Spindle Spacer
101152 Parts Pouch
101823 Inner Tube Cap Assembly with Thread Protector
100607 Fluid Retention Kit

H3 Compact Plus Water Swivel Spares Kit and Parts

H3 Head Assembly & Options

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

Part Number Description Qty
101407 Head Assembly -
100462 Spearhead Point 1
100447 Spearhead Spring 1
100463 Detent Plunger 1
100448 Spring Pin, ø7/16" x 1" Long 1
100493 Spearhead Base 1
100483 Latch Retracting Pin 2
101394 Latch Retracting Case 1
101395 Upper Latch Body 1
100484 Latch Pivot Pin 1
100450 Latch Spring 1
100496 Latch  2
100452 Stainless Steel Ball, ø22mm 1
100468 Landing Indicator Bushing with OD Groove 1
100497 Landing Shoulder 1
100498 Lower Latch Body 1
100485 Lock Washer 1
100486 Hex Nut 1
100499 Spindle 1
100487 Shut Off Valve, Hard 2
100488 Shut Off Washer 2
100489 Spindle Bearing, Upper 2
100500 Spindle Bushing 1
100457 Spindle Bearing, Lower 1
100491 Compression Spring 1
100492 Self Locking Nut 1
100502 Inner Tube Cap Assembly without Thread Protector 1
100603 Thread Protector, Inner Tube Cap 1

 

Options
Part Number Description
100551 Landing Indicator Bushing without OD Groove
100584 Shut Off Valve, Soft
101435 Solid Spindle Spacer
101152 Parts Pouch
101823 Inner Tube Cap Assembly with Thread Protector
100607 Fluid Retention Kit

HU Compact Plus Water Swivel Spares Kit and Parts

Part Number Description Qty
101389 Compact Plus Water Swivel Spares -
101354 Wavy Washer 2
101355 O-Ring, Upper 6
101356 Swivel Packing Set 3
101357 Wear Sleeve, Slotted 2
101359 Ball Bearing 1
101361 O-Ring, Lower 6
101363 Thrust Bearing 1
101365 Felt Seal 2

5

15

25

35

45

55

8

370

65

25

80

90

100

115

35

130

50

170

210

270

510

535

550

570

4

1500

1520

1540

1570

180

220

140

210

250

270

290

310

320

400

330

370

390

430

460

440

480

510

530

550

570

118

10

25

20

15

25

70

90

115

140

500

640

650

700

730

780

50

380

400

20

40

5

110

130

5

1

605

770

710

140

60

655

12

25

5

600

10

130

520

6

9

500

100

530

2

1

80

200

2

1

54.13 Litres

70.79 Litres

102 Litres - Retail $599.99

141.95 Litres

208 Litres - Retail $1038.99

300 Litres - Retail $1399.99

Day Cooler / Dry Box - Retail $99.99

Fridge / Freezer

Fridge / Freezer

Fridge / Freezer

Fridge / Freezer

With Wheels

With Wheels

With Wheels

With Wheels

With Wheels

With Wheels

With Wheels

With Wheels

With Wheels

Class 1 Div 1

Supports to up 20 lbs

Supports over 50 lbs

Class 1 Div 1

Class 1 Div 1

Class 1 Div 2

Class 1 Div 1

Utility Pole Hot Stick Light